Jump to content
SAU Community

Recommended Posts

yesterday i changed the upper and lower radiator hoses(very old) the radiator cap and the thermostat.... took it for a drive and thrashed it a little !! but the car still seened to be getting quiet hot ...... and after i unplugged the heat sensor and put it bak in the heat said half in the guage,,,, something is a miss and i just cant figure it out !! sensor? head? and there doesnt seem to be a build up of pressure on the hoses?? me is a little lost .... have i done something wrong ??

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/
Share on other sites

Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

hey thanks for the reply, air flow bottle?

coolant seems to be staying level now, and yes the thermostat is thew correct one and its in the same way the other one came out !! im hopeing it isnt the water pump... could that also be it !! and i was planning on doing the water temp sensor on the weekend.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2359920
Share on other sites

how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2360072
Share on other sites

how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

ok, but if it was the water pump wouldnt the car idle differntly? ot would the cur run differently? cause the car still kicks well

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361769
Share on other sites

it would idle the same

try driving it without the thermostat but of the bearing in the pump is f**ked it fan wont keep running straight, it wont run true to the engine

my mates fan smashed 2 radiators before he fixed his pump, bearing was screwed and the fan moved enough to foul on the radiator (r31 skyline, same shaped pump with more fins inside)

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361934
Share on other sites

Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

ok the coolant isnt staying constant, it builds up in the overflow, and ends up being like 2 inches hight then it was b4 driving it !! im not driveing iit to the stage of it over heating !! just been taking it on test drives ....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2362015
Share on other sites

ok further info !! was doing a little more work on the car today !! took it for a drive !! still doesnt seem to be much pressure in the radiator hoses?? car is running fine !1 ideling fine, but AFTER ABOUT 30 MINS OF DRIVEING the heat started to rise !! the overflow keeps filling to the stage where its about to overflow?? im starting to get worried... :teehee: its starting to look like the waterpump i think??

if so how much is a good estimate for the pump and work ?? anyhelp would be benifical

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365119
Share on other sites

Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365779
Share on other sites

Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

cool thanks for that... i think that job is a little passed my knowledge, so i might have to look into getting it done bysomeone....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2366737
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah it is really until until you get a feel for it....then it is easy. Which is no use to you really. I'd buy that torque wrench. One thing from sure, many (most?) tyre shots overtighten the f**k out of wheel nuts, so don't worry if they were tighter when you tried to take them off compared to when you do them up. I've had some crazy tight ones come back from shops, quite apart from the potential damage to the thread, I can't see a smaller person taking the wheel off on the side of the road
    • Hey mate, thread dredging hahah To answer you directly, yes I had my itbs oversized and custom butterflies etc made by EFI Hardware in Sydney back around 2017-2018 if memory serves. My setup had a vast amount of other changes too though, so no direct comparisons unfortunately. i went from oem itbs, HPI manifold and internal gate hks 2835 pro S; to 49mm itbs, cnc port matched Nismo plenum, RB25 Neo lower runner adapter hand port matched, r31house v2 Takoashi MAX equal length twin scroll manifold with twin 38mm tial gates and a FP HTA3076 with 1.01ar twin scroll real hosing. feom power Fc to a link fury wired by 12volt, r32 gtr fuel tank conversion with frenchys twin 460 / surge tabk fuel hanger combo kit, 1659cc injectors, full 4 inch turbo back stainless exhaust, Z34 6 speed, Tomei 2way with 4.3 final drive and a ton of other shit. ive posted elsewhere here with complete run down, but here's a graph from its initial tune with no boost control on, 20psi gate springs only and e85.   7542AE72-DA92-4E0B-8660-B0940FEA7F24.mov
    • On sale mate, $55. Sorted. https://www.supercheapauto.com.au/p/toolpro-toolpro-torque-wrench-1-2-drive/565734.html?utm_content=paidsearch-pmax&gad_source=1&gclid=Cj0KCQjwytS-BhCKARIsAMGJyzqYEnwWmhWf6gxTST_Nz06Gd2VePgyvL7lh6PWrQtbjXTsI6TqSCLEaAuaCEALw_wcB&gclsrc=aw.ds
    • Slap it and say it ain't going no where, you'll be fine.
    • So the whole rb25de neo setup was a tiptronic setup and i swapped everything over to my rb20de neo setup and yes even the cluster of the rb25 was swapped over. 
×
×
  • Create New...