Jump to content
SAU Community

Recommended Posts

yesterday i changed the upper and lower radiator hoses(very old) the radiator cap and the thermostat.... took it for a drive and thrashed it a little !! but the car still seened to be getting quiet hot ...... and after i unplugged the heat sensor and put it bak in the heat said half in the guage,,,, something is a miss and i just cant figure it out !! sensor? head? and there doesnt seem to be a build up of pressure on the hoses?? me is a little lost .... have i done something wrong ??

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/
Share on other sites

Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

hey thanks for the reply, air flow bottle?

coolant seems to be staying level now, and yes the thermostat is thew correct one and its in the same way the other one came out !! im hopeing it isnt the water pump... could that also be it !! and i was planning on doing the water temp sensor on the weekend.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2359920
Share on other sites

how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2360072
Share on other sites

how do you know it's overheating?

The "normal" position on the stock temp gauge will sometimes change when you install a thermostat that opens at a different temperature.

Perhaps get an aftermarket water temp gauge to see where you're actually at more accurately

Anyway, if it's definantly overheating and you've ruled out the thermostat, then it's probably the water pump.

ok, but if it was the water pump wouldnt the car idle differntly? ot would the cur run differently? cause the car still kicks well

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361769
Share on other sites

it would idle the same

try driving it without the thermostat but of the bearing in the pump is f**ked it fan wont keep running straight, it wont run true to the engine

my mates fan smashed 2 radiators before he fixed his pump, bearing was screwed and the fan moved enough to foul on the radiator (r31 skyline, same shaped pump with more fins inside)

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2361934
Share on other sites

Obvious question is did u put the thermostat in the right way and did u get the right one?

Are u using an overflow bottle with the rad?

Is the coolant level stayin constant?

If all ok replace the water temp sensor.

ok the coolant isnt staying constant, it builds up in the overflow, and ends up being like 2 inches hight then it was b4 driving it !! im not driveing iit to the stage of it over heating !! just been taking it on test drives ....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2362015
Share on other sites

ok further info !! was doing a little more work on the car today !! took it for a drive !! still doesnt seem to be much pressure in the radiator hoses?? car is running fine !1 ideling fine, but AFTER ABOUT 30 MINS OF DRIVEING the heat started to rise !! the overflow keeps filling to the stage where its about to overflow?? im starting to get worried... :teehee: its starting to look like the waterpump i think??

if so how much is a good estimate for the pump and work ?? anyhelp would be benifical

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365119
Share on other sites

Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2365779
Share on other sites

Pumps have been known to rot out the impeller blades because idiot (previous / Japanese) owners don't use proper coolant.

Pump is around $100. Job takes a (leisurely) couple of hours.

You need to remove the radiator, so while it is out, get it thoroughly cleaned.

cool thanks for that... i think that job is a little passed my knowledge, so i might have to look into getting it done bysomeone....

Link to comment
https://www.sau.com.au/forums/topic/127679-overheating/#findComment-2366737
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, while being... strictly unnecessary. Tuning is a bit like quantum physics. You don't need to understand what Schroedinger's equation actually means. You just need to run the computation and accept the answers. With tuning, you just push page up/down until the exhaust tells you that you've got the fuel right. The VE can stay hidden behind the curtain like the Wizard of Oz and you'll never need to know what he looked like.
    • The second part yes, the first part about easy VE calculation is something I've seen a few people talk about online.
    • You 100% could do that, would save money on a gym membership lol. But yeah, getting a cordless orbital sander will feel priceless coming from doing it manually.  Good luck with it mate
    • I initially was going to do the whole car with a block then realised, it would be a bigger monster of the job 😂 I guess that's all part of the learning process. I appreciate all that advice, I think I got a good idea on how to tackle this whole job.
    • I admire your efforts with the scuff pad.  As a mere mortal, I use this for the baulk of my sanding work- https://sydneytools.com.au/product/milwaukee-m18bos125-0-18v-li-ion-cordless-125mm-5-random-orbital-sander-skin-only Yes you can easily create a low spot while sanding. There are 2 types of filler, 1 part of 2 part. The 2 part filler will get used for large corrections and the 1 part filler will get used for pin holes and areas that only need slight filling.  Depending on how zealous you are with the sander (very easy to do with a power tool) or if you are chasing rust etc, yes those low spots will need to get filled or you will end up with a very obvious defects in the paint.  Using the guide coat and large sanding block, high and low areas will be revealed (watch youtube videos for a good visual on this). Its up to you if you think its worth the effort to make the car completely flat before you spray it (you make it flat by filling the low areas).  At the end of the day, it comes down to time. The end result comes from the level of prep put in to the car. If you want a perfect result, you have to put in the time during the prep stage or else it will be impossible to achieve a perfect result during the spraying process. 
×
×
  • Create New...