Jump to content
SAU Community

4wd Button On Dash


Recommended Posts

If we get some decent snow soon, I am going to drive the Stagea up. Not sure whether this has been on the forum before, but will the transmission suffer any damage by leaving it in 50/50 4wd for long periods.

Link to comment
Share on other sites

If stageas run same attesa system as GTR's, then by leaving it in 4wd for long periods of time you'll just wear out your clutch packs in your transfer case - up to you if its worth it or not. I wouldn't bother i'd just let the attesa do its job, and if it struggles (which it shouldn't) then wack it in 50/50 split...

Link to comment
Share on other sites

Its very rare for wheelspin to occur even without the 4wd button on.

The way I see it, if your wheels aren't slipping without using the 50/50 mode, then there's probably no need to use it.

Also, the way ATESSA works, I'd imagine fuel economy would suffer if you left the 50/50 4wd on all the time.

Link to comment
Share on other sites

Its very rare for wheelspin to occur even without the 4wd button on.

The way I see it, if your wheels aren't slipping without using the 50/50 mode, then there's probably no need to use it.

Also, the way ATESSA works, I'd imagine fuel economy would suffer if you left the 50/50 4wd on all the time.

Thanks for your feedback guys, guess I will just let it do its stuff, unless I am driving through a couple of inches of snow.

Link to comment
Share on other sites

Hi Hugh,

I am pretty sure that the snow button engages third gear in the auto, so that there is less slip during takeoffs in snow conditions. It's probably something that is more use in a country like Japan or NZ where there are more of these conditions, however its handy to have. ;)

Link to comment
Share on other sites

The snow button on the centre console does that (for auto's), but the S button on the dash, (to the left of the steering column) engages full time 50/50 power to the wheels.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • There is a LOT of stuff that can be done, it all depends on how much time and money you want to spend on doing in.  Not all ECUs will be able to do it, and the more control you need the more time and knowledge needs to be put into making it work.  If you're willing to spend the time and money and have the right hardware and skills involved there's a lot that can be done. 
    • I am impressed with all this level of adjustment. I didn't expect all this possibility
    • Correct.  In the case of the 500kw dyno plot I showed you the car actually runs two boost control solenoids for boost control and a 5psi wastegate spring.  It allows me to control how much boost pressure is applied to both sides of the wastegate valve at any point and fairly accurately control boost target as a result. I've tuned it so that it's able to target anywhere from 5psi to 25psi depending on what's needed.  The target tables I've set up in that car are Gear vs RPM, so every gear has potential for a different boost (and torque) curve.   First and second gear have quite low boost targets, third gear actually has different target boost all the way through the rpm range as it's a stock RB25 gearbox - the boost targets have been chosen to maintain a peak of 600nm (what the owner has set as the maximum torque he's happy with putting through the stock 3rd gear) but it carries that to the rev limiter.   The boost curve to achieve that is something of a ramp up, then hold, then ramp up again and the power curve looks more like a flat line haha.  
    • so you can decrease or increase the boost depending on the diet as you wish?     by acting on the wastegate?
    • That's torque and power, it's all from a single run.  The boost curve is "held back" from it's peak target in the 3500rpm to 5000rpm range from memory, so it ramps hard to something like 18psi then climbs more progressively to 23psi nearer 5000rpm.   It makes the torque (and power) ramp more "natural" and less hard on parts and traction, it doesn't feel artificially held back.   
×
×
  • Create New...