Jump to content
SAU Community

Recommended Posts

HI! everyone i got an R33 GTSt wrecking at the moment ,i havnt made up a list yet or price will do that on tuesday afternoon.I will take any inqurie if anyone are chasing for R33 GTST parts till the list come up .the car been hit on the left front bonnet,guard and LH door are no good.that all for now list be up on tuesday afternoon.

pm me or email me on [email protected] or call on 0415642296.din.

post-21589-1154426805.jpg

post-21589-1154426979.jpg

post-21589-1154427012.jpg

post-21589-1154427031.jpg

post-21589-1154427051.jpg

post-21589-1154427086.jpg

post-21589-1154427108.jpg

post-21589-1154427169.jpg

post-21589-1154427190.jpg

post-21589-1154427220.jpg

post-21589-1154427346.jpg

post-21589-1154427425.jpg

post-21589-1154427573.jpg

post-21589-1154427599.jpg

post-21589-1154427668.jpg

post-21589-1154427752.jpg

post-21589-1154427773.jpg

post-21589-1154427853.jpg

post-21589-1154427884.jpg

Edited by dinzlr
Link to comment
https://www.sau.com.au/forums/topic/128339-wrecking-r33-gtst-whole-cars/
Share on other sites

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

hmm dude would you have the plastic covering bit on the side of the driver seat??

You know that black looking thing, that covers the reclineably push lever thingy??

You know what im talking about?? Its just one bolt..

20bucks??

Edited by siddr20

Hey mate,

Are you willing to sell parts off the engine, or are you planning to sell it whole?

As I'm after the "U" shaped rubber hose that goes between the two vents on the rocker covers, and also the knock sensor loom.

Cheers, Ryan

hey dude you would have it.. I can see bit of it from pic 2..

look at the driver seat. Look at the bacl thing under it sorta..

You know when you put the lever up so the seat reclines..

Hmm i dont have camera to take a pic of mine..

look at pic 2, you can see it..

Edit: This pic: http://www.skylinesaustralia.com/forums/in...st&id=49430

Edit 2: How much for that gtr wing?? Cheers

Edited by siddr20

Do you have the plastic bit under the drivers side? Under the steering colum, the plastic that covers the fuses and the wiring under it etc.. $10?

Driver side floor mat?

Power steering pump? (Just want a rough est on price)

And if you are wreaking engine (though I doubt it) CAS Whole unit.

Cheers

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hmm. Yes. I should have been clearer. 1000s for Haltech, for extra headroom. 725s for Nistune. You might even be OK with 640s, but if the possible power ends up much more than 300 rwkW you will run out of headroom on the 640s. That would probably be OK and a signal to not push it to that sort of power with Nistune anyway. At that level you probably do want to be thinking about engine protection functions. Oh, and all of that presumes 98 only, not E85. Well....the 1000s would allow you to run E85 at ~300rwkW territory, again, maybe sort of running out of headroom. Hard to tell with E85 - depends on the tuner as to how rich they like to set it up.
    • Yes.  The only scenario I can imagine when the answer isn't yes, is if you drive like there is highway patrol behind you at all times.  If your car currently runs, enjoy it and keep saving. Better costs more, keep saving until you can budget the better ECU. It's worth it.  Nope. Plenty of us making >300kw on unopened motors. Mine is unopened and makes about 350kw if I turn everything up, its fine (lots of caveats here, how the car will be used/abused, how long you expect the engine to last between rebuilds, how has the engine been maintained prior to coming into your ownership, etc etc).   
    • Sorry just wanting to clarify, at this power goal, which should I be going? Also, More info regarding suspension, the rear upper camber arms were used to get the camber back to i believe around -0.5 ~ -1 degree (@ Road and Race in Rydalmere), I forgot the exact figure, but ALOT less camber than what it came originally which was like -2.5degrees. Are the traction arms still recommended? The bilsteins from SydneyKid, they've got 400lb/in fronts & 275/in in the rear, revalved to his specs. Intercooler, I'm just having a look at some on Rakuten.jp and some other japanese sites. Might get something from back there, GReddy, Blitz or HPI, all crossflow. Looking at roughly $450-$500 AUD + shipping... Theres not many choices except that chinese branded Justjap unless you go for blitz return flow. Yeah, only downside with Haltech is the price ahhaha, so expensive, and with all the sensors if I go that route... $$$$$ yeesh. Are headstuds/gaskets needed for <300akw?
    • Haltech fanboi reporting in. Buy the Haltech! 
    • You can try shoving a borescope down there to see what's up.
×
×
  • Create New...