Jump to content
SAU Community

VINS you want "fasted"


Recommended Posts

Is this a genuine 1999 260RS Autech?

VIN Number 6U900WGNC34131750

Looking to buy one as our first Family car, i have found one but i just want to make sure its Genuine.

Cheers

post-3573-0-97072900-1318559700_thumb.png

Link to comment
Share on other sites

hi guys,

just had a look and it says my VIN is:

6A91MPORTXHWL4001

Its a 2/99 GTSt R32

can u make any sense of that?

cheers

Nathan.

That should be your import/compliance plate. The VIN we are after should be on the left-hand side of that one, on a green plate. =-]

Link to comment
Share on other sites

some pics...

Yep, like that plate Nathan.

From experience, if the plate has been remade and has funny letters like 1MPORT, the VIN never works.

As it is, I tried this VIN: HCR32 094224 and it doesn't work. It could be an Australian delivered R32, I dunno... but the VIN that is pressed onto the firewall (under the plate) looks odd too.. The leading "H" is not straight.

I really don't know why this is.

Link to comment
Share on other sites

No good. Do you want to confirm the plate? BNR34 402974. It might not start with a "4".

Hi Randy,

The number I gave you is correct; both on the firewall as well as the plate. A puzzle?

Regards T

Link to comment
Share on other sites

The URL for those images is "/.../2011 NUR/Matthew-5.jpg" - is it a NUR Spec car???

If so, were they re-numbered by the factory when they were rebuild from their first incarnation as a 'normal' GT-R?

Link to comment
Share on other sites

You can tell that just by the colour of the build plate ;)

Nurs didn't get a special build, they followed the normal build sequence for 34s. Most people have the early edition of FAST which cuts off somewhere in late '01, meaning Nurs won't decode on them.

Link to comment
Share on other sites

Hi Randy,

The number I gave you is correct; both on the firewall as well as the plate. A puzzle?

Regards T

Could be! The number is quite high, so if your car was made after 2001, my CD's don't cover it. =-[

-Steve

Link to comment
Share on other sites

You can tell that just by the colour of the build plate ;)

Nurs didn't get a special build, they followed the normal build sequence for 34s. Most people have the early edition of FAST which cuts off somewhere in late '01, meaning Nurs won't decode on them.

Yes, this. =-]

My discs are 2001.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...