Jump to content
SAU Community

Recommended Posts

when i start the car up the idle drops after warm up time to bou 850 -900rpm.

after a while the revs will occasionally raise to a little above 1000rpm without touching the accelerator and if i turn the wheel when stopped the revs drop to bout 550 - 600rpm?

is this a problem because it gets relu anoying??

I have allready cleaned the acc valve so thats not the problem --> any other suggestions????

what else could be the problem??

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/
Share on other sites

hey man,

look in the tutorial section for "Cleaning you AAC valve"

i can almost guarantee this will fix your problem.

after time the aac valve gets full of crud and carbon build up.

spray it out with carby cleaner and put it back together.

its easy as to do, im pretty useless at diy now i can do it in like 30 mins.

cheers

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/#findComment-2385637
Share on other sites

hey man,

look in the tutorial section for "Cleaning you AAC valve"

i can almost guarantee this will fix your problem.

after time the aac valve gets full of crud and carbon build up.

spray it out with carby cleaner and put it back together.

its easy as to do, im pretty useless at diy now i can do it in like 30 mins.

cheers

That could be something as simple as the idle up for the a/c compressor. Is the a/c on when this happen?

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/#findComment-2386029
Share on other sites

as already said, the turning of the wheel is the cause of the revs dropping due to the power steering pump needing power.

when the revs go up do they stay there for a little while, or does it jump up and down? if it goes up and stays there for a while then drops, it could be the air con, as godzilla32 said.

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/#findComment-2390914
Share on other sites

its not meant to...it explains why the idle drops when you turn the wheel
as already said, the turning of the wheel is the cause of the revs dropping due to the power steering pump needing power.

when the revs go up do they stay there for a little while, or does it jump up and down? if it goes up and stays there for a while then drops, it could be the air con, as godzilla32 said.

as mentioned i am sitting in the car start it up and sit there - dont touch the wheel dont put my foot on the cluch dont turn the a/c on - nothing

it still idles rough - jumps between 1000 and 600 rpm and sometimes misfires

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/#findComment-2405510
Share on other sites

Hmm I have a similar problem (R33 gtst)

Start the car, works fine, cold, idles at 1100 or so. Warm, will idle at 900 rpm no worries. However, if im crawling at an intersection or in heavy traffic, if I move forward, then to stop just put the clutch in and stop, the revs drop not to idle like they should but to very low, like 200-500 rpm, the engine shudders abit, then jumps back upto 900rpm idle and is fine. But it keeps threatning to stall everytime it does this?

Link to comment
https://www.sau.com.au/forums/topic/128735-idle-problems/#findComment-2405760
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's one I help build and tuned a decade ago, Garrett  GTX3071R Gen 1, T3 twin scroll 0.83 rear housing. Went from larger 272 cams down to smaller Tomei Poncams to help with the low end. S13 non VCT motor. Car was purpose built for the track, hence low down was the focus. Note the actual dyno chart shows lower boost, however the EBC and boost gauge showed 1.9Bar (Ignore the torque, I was young and didn't know how to set derived torque)  
    • I’m doing some side developments on SR20det S13 engines, its one my hobby cars used it to compare flow capacity of some smaller size wheels. SR20det is one of another JDM legendary engines I'm sure there are plenty of SR enthusiasts on this forum, I will share results some common turbo configurations here. a quick run down of what the car is: Wide body 180sx Type X with black top engine (blue). It has: Stock bottom end Haltech 1500 ECU 5-0 motorsports trigger kit Kelford SR20DET Beehive Spring with Titanium Retainers Kelford Cams SR20DET S13 188-B 268/272 Cams G25-660 Turbocharger in T2 .64 rear housing internally gated ARP Head studs MLS head gasket 1000CC ID injectors Walbro 450L Fuel pump Front mount cooler kit JJR’s 3 inches turbo back exhaust (its too short for the 180sx it had to be extended) Pump 98 fuel Hub Dyno tune So far made 270rwkws at 22psi full boost by 4500RPM. Engine is very knock limited hence a pretty bad looking top end. From previous experiences it seems like SR20dets are happier with bigger size turbine, some thing like a GT30 would make way better top end, but on same time response is lost. It won't be a problem with S15 VCT engines. I'll be testing alternative turbine housing, turbine wheel and possibly dump pipe options for extra flow to resolve the problem and of course E85 would resolve all the issues.            
    • Awesome writeup and details. Thanks for sharing the story so far. I can relate to parts of it with my previous car and some of the issues I had to deal with.
    • Wow the colour matched hard top completely transforms the car. Are there any nice front lip options for the car or is that off the table?
    • Generally yes but for some reason I've been ruthless this time around!  I might even need to do another tip run after the way I've finally been able to hit the delete button on shit I've stepped over, stepped around and tripped over for the past 10 years!
×
×
  • Create New...