Jump to content
SAU Community

Recommended Posts

17" white PIAA Racing rims for sale, they are made in Japan and in good condition. Would swap for 17x9, offset +20(GTR offset) rims. Tyres on them are worn out.

17x8, offset 35 and 17x9,offset 38, 5 x 114.3, great for gts-t and other cars with similiar fitting.

Location: Brisbane

Reason for sale: Wrong offset for GTR

Price: $700

PM me or call/sms 0433553356.

Cheers~

post-23256-1154622044.jpgpost-23256-1154622012.jpgpost-23256-1154622196.jpg

hmm.. what size is the tyres and how much threads is left on them?

thanks.

Link to comment
https://www.sau.com.au/forums/topic/128785-soldpls-delete/#findComment-2384441
Share on other sites

As per first post, tyres on the rims are worn out and no good. I personally wouldn't even want to sell them to you with the tyres, the fronts might do some kms,rears are gone, in fact ill most likely remove the tyres for the eventual buyer and save you guys from the trouble of doing it and having to pay levy for getting rid of them.

Cheers~

Link to comment
https://www.sau.com.au/forums/topic/128785-soldpls-delete/#findComment-2384496
Share on other sites

im located just out of brisbane in ipswich.. is it posible to come check em out before i buy? what part of bris you in? and would you take $550 pickup

also is the dish any different front to back?

thanks

Edited by 2gceffy
Link to comment
https://www.sau.com.au/forums/topic/128785-soldpls-delete/#findComment-2385284
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good to hear. Hopefully you're happy enough not to notice when driving and just enjoy yourself.
    • I mean, most of us just love cars. Doesnt necessarily have to be a skyline.
    • Did you pick up a manual cluster to remove the position indicator?  (Pretty sure the 34 has the gear position in the cluster, but it's been a while)
    • Here is a recipe. Sonic blocks till you get one that has a good enough bore. Get a torque plate and block brace, use your choice of fasteners (arp ect) bolt the thing together empty, half fill it and let it cure. Release it when it has, go to a REPUTABLE RB Builder and get the thing line bored/honed and cylinder honed to size, then wash. Once its all clean and dandy, wash and blow it out again. Then again.  Assemble said engine to your desired clearances with oil control mods, gasket to suit desired CR/Squish ect. Attach your extended sump with proper trap door oil baffles and head drain plumbed to sump with a SUMP BREATHER SYSTEM. Build your front diff with a decent LSD, rebuild your transfer case with a few extra plates, more than likely replace your tailshaft centre bearing and tighten up the rear diff. Tune to minimise excessive midrange cylinder pressure (timing unless you like to split bores and rebuild engines) Enjoy your engine, but hate the fact you are now destroying engine mounts, gearboxes, gearbox mounts, diff output flanges and driveshafts, diff mounts, tailshafts and front CV's.   Disclaimer.... Ive never done any of the aforementioned stuff.......
    • 440s will support well over 400HP on petrol, which is a decent place to be for an RB20. 230+rwkW. Will be a safer bet for idle/low load. 550s would be nice for the extra headroom. I've made the same decision with mine (Neo25). 1000s are probably too big for the Nistuned ECU, so I have some smaller ones.
×
×
  • Create New...