Jump to content
SAU Community

Recommended Posts

Hi all,

Its been a while since i've been on here as I sold my 34GT-t. Now i'm looking at selling my current car and returning to the Nissan fold. My question is this, what benefits does the R33 GTR have of the R32 ?? Am I still able to pop the ATESSA fuse on the 33 and put it into RWD mode on the 33 ?

Chris

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/
Share on other sites

or get an attessa controller bluprint :thumbsup:

advantages the 32 has over the 33.

stock, the 32 beats the 33 performance wise.

obviously the 33 has slightly more responsive handling etc due to steering upgrades etc.

but the 33 interior is a bit, disappointing really.

I have been looking at both recently and read many reviews. They say out of all 3 gtr's, the 32 is the most chuckable, and it's also the most fun to drive out of all 3.

Match that with good prices, great performance, the best looks IMO (34's rank second just because they're so aggressive but I think they are too big) and the ability to pop the fuse (if you want) then you have a great car.

Attessa controllers to disable the front drive on 33's and 34's CAN be expensive, but I would view it as an investment to greater handling at the same time as you could then tweak the 4WD better and create a better handling car for road / circuit use.

GO THE 32 :dry: I am.

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2405296
Share on other sites

ALL GTR'S ARE EXPENSIVE TO FIX.

:thumbsup: you should know that by now.

as for the age. I'm getting a 94 model because like you I was slightly concerned with that. But seriously, anything old can be upgraded or replaced. If the interior gets tired, re trim it. If the body is in bad nic, re do it.

Everything comes down to money.

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2405628
Share on other sites

ALL GTR'S ARE EXPENSIVE TO FIX.

:) you should know that by now.

as for the age. I'm getting a 94 model because like you I was slightly concerned with that. But seriously, anything old can be upgraded or replaced. If the interior gets tired, re trim it. If the body is in bad nic, re do it.

Everything comes down to money.

Yeah, this is true. I'm currently driving an 02 STi, but want to return to RWD (i like skids :no:). I was looking at an FD RX7 but they are still priced too highly. The GTR seems to be the best all round car for what I want.

Edited by Binky1970
Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2405735
Share on other sites

for the R33

Age

looks more modern (way better in my opinion)

R33 has a upgraded ATTESSA system its a faster car around a racetrack in factory form

R33 is more refined / comfortable

For the R32

slightly quicker in a straight line.

hardcore racer

more fun to drive

Have a read of the specs on my website.

http://nissanskyline.6te.net

cheers

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2430780
Share on other sites

I don't like the way people seem to love 32's cos they are "faster" Only in a straight line. Around a race track a 33 and 34 GTR would be faster. Nissan wouldn't of gone backwards. Anyone can redline a car and drop the clutch it takes a bit more skill to go around some corners.

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2431670
Share on other sites

Bang for buck go a 32.

Faster isnt always better. Im old skool love the look. Dislike the 33's would rather a 34. but since i cant have that (well i can but i choose to see the world instead.. hrrm hard choicce) im saving my pennies for a 32. well i aint saving. I told my boss id stay if he gave me 10K cash in hand in january! lmao whe i get back from OS he said ok son

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2432565
Share on other sites

But you have to remember if you do the same mods on a 32 as a 33 the power gained will be greater on a 33. Same goes for the 34.

Chris

Ummm why is that? all have rb26dett, obviously minor upgrades from one to the other, but i dont understand how you have come to this determination...

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2432852
Share on other sites

Ummm why is that? all have rb26dett, obviously minor upgrades from one to the other, but i dont understand how you have come to this determination...

Better: engineering, turbo's, intercoolers, dump pipes, etc.

If you still dubt it, look in HPI issue 51 ;)

PS: If i had to choose between a R32 or R33 GTR, i would personally go for the R32. I love my 33 GTST, and chose a 33 over a 32 GTST, but when it comes to GTRs i always prefered the 32.

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2433133
Share on other sites

Ummm why is that? all have rb26dett, obviously minor upgrades from one to the other, but i dont understand how you have come to this determination...

If they were all the same why would people lash out and spend money on a newer model. As they other guy has stated things get revised with a each model you dont think they would be exactly the same do you?

Chris

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2434589
Share on other sites

If they were all the same why would people lash out and spend money on a newer model. As they other guy has stated things get revised with a each model you dont think they would be exactly the same do you?

Chris

Of course they are not the exact same and i never said that, and obviously people will pay more for a newer model, but i would have thought, that the basic engine is very similar and to say that a 33 gtr will always respond better to mods than a 32 gtr (especially when you consider the weight of the cars) i would not have agreed with.

Also I would consider the fact that the 32gtr in straight line was quicker than the 33 to start with.

Link to comment
https://www.sau.com.au/forums/topic/130024-choices/#findComment-2435047
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...