Jump to content
SAU Community

Recommended Posts

yeh i've been there bro i no wat a wastegate does but am i betta of wid and external wastegate?

and if i do put da external wastegate will it flutter ssss tsh tsh sth tsh like those (no go) VLs???

Edited by assyrian4evaa

a wastegate makes no noises. you have an internal wastegate'd turbocharger. fitting an external wastetgate achieves nothing. if you want vl turbo flutter or compressor surge then block off your bov or remove it completely

yeh i've been there bro i no wat a wastegate does but am i betta of wid and external wastegate?

and if i do put da external wastegate will it flutter ssss tsh tsh sth tsh like those (no go) VLs???

you most certainly have not by reading what you have just posted, you dont know how a wastegate (internal or external) works :P

If you read www.howstuffworks.com

You would find that a wastegate is not, and has nothing, to do with compressor surge cause by the non-fitment of a BOV.

This has been covered many many times before.

Please use the search button

NOO u guys dont undastand FLUTTER is NOT wat i want..

heaps of ppl always say dat if i do put da wastegate that it WILL have this VL flutter bullshit so i didnt want that

wat i want to know is whether its worth it or not performance whise

a wastegate makes no noises. you have an internal wastegate'd turbocharger. fitting an external wastetgate achieves nothing. if you want vl turbo flutter or compressor surge then block off your bov or remove it completely

so wat happens 2the compressed air if u remove da bov?

so wat happens 2the compressed air if u remove da bov?

that caused the "flutter" or compressor surge

the air is compressed up against the closed throttle, then has to go somewhere, so it heads for the only opening it has ... back through the turbo... that moving air is "chopped" up by the compressor wheel of the turbo .. creating flutter as the air leaves the air filter/pod

normally it would go through the BOV and get either released to the atmosphere, or back into the piping before the turbo.

so its no good 4da turbo 2remove da bov?

big debate on whether it is or it isn't

VL turbo dont have them std .. skylines all do ..

my thoughts, are if it had it, then keep it or upgrade it if you can ..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...