Jump to content
SAU Community

Recommended Posts

  NewKleer said:
ive got about 10 of the 50 remaining, which will be taken by the remaining people on the list (on here and pga). do u want me to add u to the list? (u might get in if people are too slow/dont want one). otherwise next batch will be around january

Yesss please... arghh i didnt see them on pga >.<

  • Replies 279
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

This is mine set up on the dash. You can see most of all the dash displays etc and its not distracting because the ECU display is not bright but perfectly readable. The cables can be tucked neatly under the ledge into the steering column cavity and through the inside of the dash so are not untidy and the RS232 plug can reach through to the pas seat to a laptop OK. I only used a small pad of velcro at each end as its so strong and makes the unit hard to remove if you use the full length.

post-12111-1164153443.jpg

The photo is chopped tthough as the flash was stuffing it up. An extremely handy device but I still am not sure what values I should be seeing at initial power on and then at idle etc.

Peter can you list some typical values of all sensors?

batt: <12 car not on, ~14v running

eco: 99.9 (infinite) when car not moving, 20->99 under acceleration, <20 cruising (assuming set up in options)

inj: ~5-10% on cold warmup, 0-3% normal idle, 3-100% depending on load. 100% peak doesnt necessarily mean your injectors have maxxed out, you need to hop on a dyno to work out this

timing: anything thats BTDC, big jumps down from like 30 to 3/5 under load may indicate pinging/det (logging will help here). if timing jumps around from ~3 to 15 or so at idle, your closed TPS switch may not be staying shut properly.

aac - auxiliary air control, lets air into engine bypassing throttle, will be high (~90) on startup/AC on, but should fall to around 20-40 when running normally

o2: 0.3v till sensor warms up (30s), then swinging between 0.1->0.9v and back continually when cruising. from memory, 1v = rich, 0v = lean. on decel/engine breaking will probably go lean, and rich on acceleration

engine temp: "warmup" time typically to around 60-65C mark, then normal operation. be worried if it gets close to 100, but in low/mid 90s is generally fine.

AFM: generally corresponds to load of engine, 0.5v when not running, 1.0-1.2 idle (after warmup), if this hits 5v then you're probably getting close to peak power for current AFM (should determine this on a dyno).

tps: ~0.5v closed, ~4.5v WOT, and linear in between (roughly)

Hey Peter, my unit just arrived, thanks mate!

I haven't used it as yet but I have to say I'm very impressed with the unit itself, and your packaging. Very professional.

Can't wait to try it out

Dane

  • 2 weeks later...

i may have a couple of left over enclosures (ones that didnt closer perfectly for one reason or another) that i can probably fix u up with whenever i do next upgrade.

just tape sides with electrical tape for time being (depending how bad it is). it's the front lips bent out a bit?

  NewKleer said:
i may have a couple of left over enclosures (ones that didnt closer perfectly for one reason or another) that i can probably fix u up with whenever i do next upgrade.

just tape sides with electrical tape for time being (depending how bad it is). it's the front lips bent out a bit?

Haha I did tape it up..

Its the back of it that has lifted up mainly on one side

regarding the peak values that it shows, they seem to be reset automaticaly once the ignition switched off and then on? is this the way it should be? i see there is a 'clear peak values' option but it seems to do it by itself...

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...