Jump to content
SAU Community

Recommended Posts

Heya, is it possible to use a laptop instead of ecu? If so there would be a hell of a lot of advantages, not to mention it would be cheaper for the equipment and tuning.

Imagine getting a new part installing it, then installing the software that came with the part?

sound possible? I dont know alot about cars so excuse me if its a silleh question.

ta.

Link to comment
https://www.sau.com.au/forums/topic/131388-laptop-instead-of-ecu/
Share on other sites

If you had the knowledge and resources, sure but the main thing here is how would you feel if your $500 laptop-ecu hybrid that you choose to use failed while driving. Imagine all the R&D that has gone into current ECU's and there is a very good reason why they cost so much.

Interesting idea, but to be honest a dedicated ECU is still the best bet IMHO.

It's designed to do the job, and doesn't have processing overheads like running an operating system (eg Windows, Unix) or background operations that don't directly contribute to the running of the vehicle. Unless the laptop runs full-time, you'd need to wait 10 seconds or more from when you turn the key to the time that things start to work. If data needs to come from the hard drive, there'll be a pause which could be detrimental. You would also need to make your own high-speed interface to send and receive signals on the hundred or so wires going in and out of the computer.

Aftermarket ECUs are already programmable and cheaper than most laptops to buy. Installing software that came with the part is an interesting idea too, though the point of programmable management is that you can tune the fuel and ignition maps to exactly match the characteristics of your engine. The way a certain part affects the optimum tune for your engine depends not just on the part itself, but also on what else is bolted to the engine, the flow characteristics of the intake and exhaust systems, engine wear, etc. Tuning each car individually is still the best way.

Nice idea though :O

Hey,

I don't think you need a hell of a lot of processing power to run a car. Car ecu's are pretty basic as far as mips and speed, compared to todays technology. There really is not a great deal to it, some sensor inputs, calculations, and timing and injectors to control. Some other thing like idle controller etc. No monitor matrixes, or human language to deal with, all binary input and output. Most advances in car computer are in the software.

Besides, I found a list of issues that might happen if you proceeded...(for a laugh)

1. Every time they repainted the lines on the road, you'd have to buy a new car.

2. Occasionally your car would just die on the motorway for no reason, and you'd have to restart it. For some strange reason, you'd just accept this, restart and drive on.

3. Occasionally, executing a manoeuvre would cause your car to stop and fail to restart and you'd have to re-install the engine. For some strange reason, you'd just accept this too.

4. You could only have one person in the car at a time, unless you bought a "Car 95" or a "Car NT". But then you'd have to buy more seats.

5. Apple would make a car that was powered by the sun, was twice as reliable, five times as fast, twice as easy to drive - but it would only run on five percent of the roads.

6. Macintosh car owners would get expensive Microsoft upgrades to their cars which would make their cars go much slower.

7. The oil, engine, gas and alternator warning lights would be replaced with a single "General Car Fault" warning light.

8. People would get excited about the "new" features in Microsoft cars, forgetting completely that they had been available in other cars for many years.

9. We'd all have to switch to Microsoft gas and all auto fluids but the packaging would be superb.

10. New seats would force everyone to have the same size butt.

11. The airbag system would say "Are you sure?" before going off.

12. If you were involved in a crash, you would have no idea what happened.

13. They wouldn't build their own engines, but form a cartel with their engine suppliers. The latest engine would have 16 cylinders, multi-point fuel injection and 4 turbos, but it would be a side-valve design so you could use Model-T Ford parts on it.

14. There would be an "Engium Pro" with bigger turbos, but it would be slower on most existing roads.

15. Microsoft cars would have a special radio/cassette player which would only be able to listen to Microsoft FM, and play Microsoft Cassettes. Unless of course, you buy the upgrade to use existing stuff.

16. Microsoft would do so well, because even though they don't own any roads, all of the road manufacturers would give away Microsoft cars free, including IBM!

17. If you still ran old versions of car (ie. CarDOS 6.22/CarWIN 3.11), then you would be called old fashioned, but you would be able to drive much faster, and on more roads!

18. If you couldn't afford to buy a new car, then you could just borrow your friends, and then copy it.

19. Whenever you bought a car, you would have to reorganise the ignition for a few days before it worked.

20. You would need to buy an upgrade to run cars on a motorway next to each other.

LOL, a few good points.

Of course the program being run via a PC would have no net access so you wont have anything on the laptop other then whats needed. So hopefully no stupid issues. Also the software will take into account what other parts are installed. Would this reduce dyno time by much? never used a dyno before.

Theres idea is more for modifieing cars only. Not trying to sell it to Holden or anything :O

But perhaps a laptop and an ECU and take away some of the features from the ECU leaving it with things like airbags, ABS and all the regular stuff.

Once i get my car i am really going to look into this. If an ECU can be remapped that means the data can be stored, and then transfered to a laptop anyway.

Another issue would be installing a "legit" version of windows... or maybee do it via linux :D

these are just ideas people. SO thanks for your input so far.

Edited by interkool

why is it unreliable? an ECU is a computer without a screen, so It isnt much different.

by the way if you disconect the laptop no one can steal your car. :(

Well i have started to talking to a couple of people about it that can help make this possible. If any one has any helpful ideas, then please PM or add to this Topic.

Thankyou for everything so far.

Edited by interkool

A laptop also has a storage method involving a magnetic head whizzing a few millionths of an inch above a rotating platter. What happens when you hit a couple of solid bumps... your car dies? great! time to call a tow truck.

What interface method do you plan to use between your "laptop ECU" and all the engine sensors?

It's going to cost you more than an aftermarket ECU to make. And it'll be shit. Unless you write your own real-time operating system. Things like injector pulses can't be delayed because windows feels like paging something out to the disk first.

Yeah, but you can get disk on chip... Solid state. Anyway PC ECU, it's not practical.

I think a good idea would be to have a computer giving you all the readouts on a LCD screen installed somwhere in the car, like the dash, or even above the dash and have it reflect off the screen, like a HUD. The pc would plug into the data port of the ecu. When I was at the tuners, he had a diagnostic program that gave you every readout possible, like speed, temp, o2 sensor voltage, MAF voltage, the works! You could almost get rid of all the dials in the dash and use an LCD. I don't know aboout the warning lights though, the ECU may not control all of them, like high beam for instance... But you could also incorporate other things like a reverse camera. Just an idea.

The problem is that I though of this a while ago, and the mercedes make an s class that already has all of this.

damn Jarmans...

>why is it unreliable? have you used a laptop before? do you realise and ECU is a computer without a screen?

er...many of the electronics we use today are, in vague terms, 'computers without screens' (e.g. microwave, dvd recorder etc). but i would much rather trust a dedicated device to handle my car than a laptop ('specially one running something like XP).

>by the way if you disconect the laptop no one can steal your car.

sure they can. flatbed truck.

For a laptop to emulate the code contained within the ecu's specialist chips I think you will find the processing power required is considerable.

Very similiar to that of a mobile phone; try to create software that does what the specialised chips do in a mobile phone and you will need a computer half the size of your bonnet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks, I removed the fuse and the relay from the car and made my own circuit with them to test them with a test bulb.  I will look for the wiring diagram and go from there.
    • Jdm DC2R is also nice for a FF car compared to the regular hatches of the time.
    • Now that the break-in period for both clutch and transmission is nearly over I'd like to give some tips before I forget about everything that happened, also for anyone searching up how to do this job in the future: You will need at least 6 ton jack stands at full extension. I would go as far as to say maybe consider 12 ton jack stands because the height of the transmission + the Harbor Freight hydraulic platform-style transmission jack was enough that it was an absolute PITA getting the transmission out from under the car and back in. The top edge of the bellhousing wants to contact the subframe and oil pan and if you're doing this on the floor forget about trying to lift this transmission off the ground and onto a transmission jack from under the car. Also do not try to use a scissor jack transmission lift. You have to rotate the damn thing in-place on the transmission jack which is hard enough with an adjustable platform and a transmission cradle that will mostly keep the transmission from rolling off the jack but on a scissor lift with a tiny non-adjustable platform? Forget it. Use penetrating oil on the driveshaft bolts. I highly recommend getting a thin 6 point combination (box end + open end) wrench for both the rear driveshaft and front driveshaft and a wrench extension. These bolts are on tight with very little space to work with and those two things together made a massive difference. Even a high torque impact wrench is just the wrong tool for the job here and didn't do what I needed it to do. If your starter bolts aren't seized in place for whatever reason you can in fact snake in a 3/8 inch ratchet + 6 point standard chrome socket up in there and "just" remove the bolts for the starter. Or at least I could. It is entirely by feel, you can barely fit it in, you can barely turn the stupid ratchet, but it is possible. Pull the front pipe/downpipe before you attempt to remove the transmission. In theory you don't have to, in practice just do it.  When pulling the transmission on the way out you don't have to undo all the bolts holding the rear driveshaft to the chassis like the center support bearing and the rear tunnel reinforcement bar but putting the transmission back in I highly recommend doing this because it will let you raise the transmission without constantly dealing with the driveshaft interfering in one way or another. I undid the bottom of the engine mount but I honestly don't know that it helped anything. If you do this make sure you put a towel on the back of the valve cover to keep the engine from smashing all the pipes on the firewall. Once the transmission has been pulled back far enough to clear the dowels you need to twist it in place clockwise if you're sitting behind the transmission. This will rotate the starter down towards the ground. The starter bump seems like it might clear if you twist the transmission the other way but it definitely won't. I have scraped the shit out of my transmission tunnel trying so learn from my mistake. You will need a center punch and an appropriate size drill bit and screw to pull the rear main seal. Then use vice grips and preferably a slide hammer attachment for those vice grips to yank the seal out. Do not let the drill or screw contact any part of the crank and clean the engine carefully after removing the seal to avoid getting metal fragments into the engine. I used a Slide Hammer and Bearing Puller Set, 5 Piece from Harbor Freight to pull the old pilot bearing. The "wet paper towel" trick sucked and just got dirty clutch water everywhere. Buy the tool or borrow it from a friend and save yourself the pain. It comes right out. Mine was very worn compared to the new one and it was starting to show cracks. Soak it in engine oil for a day in case yours has lost all of the oil to the plastic bag it comes in. You may be tempted to get the Nismo aftermarket pilot bearing but local mechanics have told me that they fail prematurely and if they do fail they do far more damage than a failed OEM pilot bushing. I mentioned this before but the Super Coppermix Twin clutch friction disks are in fact directional. The subtle coning of the fingers in both cases should be facing towards the center of the hub. So the coning on the rearmost disk closest to the pressure plate should go towards the engine, and the one closest to the flywheel should be flipped the other way. Otherwise when you torque down the pressure plate it will be warped and if you attempt to drive it like this it will make a very nasty grinding noise. Also, there is in fact an orientation to the washers for the pressure plate if you don't want to damage the anodizing. Rounded side of the washer faces the pressure plate. The flat side faces the bolt head. Pulling the transmission from the transfer case you need to be extremely careful with the shift cover plate. This part is discontinued. Try your best to avoid damaging the mating surfaces or breaking the pry points. I used a dead blow rubber hammer after removing the bolts to smack it sideways to slide it off the RTV the previous mechanic applied. I recommend using gasket dressing on the OEM paper gasket to try and keep the ATF from leaking out of that surface which seems to be a perpetual problem. Undoing the shifter rod end is an absolute PITA. Get a set of roll pin punches. Those are mandatory for this. Also I strongly, strongly recommend getting a palm nailer that will fit your roll pin punch. Also, put a clean (emphasis on clean) towel wrapped around the back end of the roll pin to keep it from shooting into the transfer case so you can spend a good hour or two with a magnet on a stick getting it out. Do not damage the shifter rod end either because those are discontinued as well. Do not use aftermarket flywheel bolts. Or if you do, make sure they are exactly the same dimensions as OEM before you go to install them. I have seen people mention that they got the wrong bolts and it meant having to do the job again. High torque impact wrench makes removal easy. I used some combination of a pry bar and flathead screwdriver to keep the flywheel from turning but consider just buying a proper flywheel lock instead. Just buy the OS Giken clutch alignment tool from RHDJapan. I hated the plastic alignment tool and you will never be confident this thing will work as intended. Don't forget to install the Nismo provided clutch fork boot. Otherwise it will make unearthly noises when you press the clutch pedal as it says on the little installation sheet in Japanese. Also, on both initial disassembly and assembly you must follow torque sequence for the pressure plate bolts. For some reason the Nismo directions tell you to put in the smaller 3 bolts last. I would not do this. Fully insert and thread those bolts to the end first, then tighten the other larger pressure plate bolts according to torque sequence. Then at the end you can also torque these 3 smaller bolts. Doing it the other way can cause these bolts to bind and the whole thing won't fit as it should. Hope this helps someone out there.
×
×
  • Create New...