Jump to content
SAU Community

Fs - Damaged R32 Type M And R31 - Newcastle


Recommended Posts

Hey all,

I have a Type M R32 for sale. I was the first owner of the car in Australia and only had it a few months until unfortunately i decided i would casually drive into a parked car. I'm selling car complete and it cannont be driven due to having no front left wheel. It can be started though. Everything on car is in excellent condition including motor. Damage was done to front left and was quoted $11-12000 to get it fixed. Dont have pics of damage yet but will as soon as i can.

Im looking for $5000 ono. Details are,

  • It has 81,000 kms. Motor is in excellent condition. Manual Gearbox.
  • Nardi Steering wheel
  • Mines Chipped ECU....removed factory boost cut, speed and rev limiter
  • Full 3" exhaust with standard cat
  • Practically brand new stainless split 3" Dump pipe
  • Good tread on all tires
  • Strut Brace
  • Interior in excellent condition
  • GReddy full auto turbo timer. (Shows speed, 0-100 ,0-200 , 400m timing etc)

Car is complete and dont want to seperate anything. Would rather someone buy the car as is.

Car can be started and run for as long as u desire just can't be driven.

Pics Before accident.

post-26525-1156560241.jpgpost-26525-1156560276.jpg

post-26525-1156560321.jpgpost-26525-1156560338.jpg

Pics After Accident:

post-26525-1156758815.jpgpost-26525-1156758969.jpg

post-26525-1156759120.jpgpost-26525-1156759333.jpg

post-26525-1156759607.jpgpost-26525-1156759789.jpg

Also for sale is an Auto r31 executive.

Around 250,000 kms. A very reliable car. Needs new tires and runs out of rego soon.

Looking for around $1000. Pic also attached.

post-26525-1156560199.jpg

Can contact me by ringing 0412 643 708

Or by e-mailing me [email protected]

By phone would be best.

Cheers,

Andrew

Edited by knrd
Link to comment
Share on other sites

Will get pics of damage tomorrow. It would be best to buy for parts but if your keen enough could be fixed with a bit of time on the straightening jig. The control arm broke and the passenger side wheel went pusing into the floor. It ripped apart abit of the firewall which would be fairly time consuming to fix i'd imagine. It's a shame cause apart from that the rest of the car is perfect. I cancelled rego seeing as i chose to not get it fixed. Has all been complied and was rego'd until i cancelled it to get back a little bit of money. Could easily be re-registered if you decide to fix it but i would see it better going to someone after lots of parts, or after the engine and accesories.

Cheers,

Andrew

Edited by knrd
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • I am going to chime in here and say that is very bad advice for a built motor, making decent power of 400kW+ Especially if the rings have been gapped on the looser side. The more power you make the heavier you need your oil to be to be able to maintain that suspension between the moving parts, if not you'll have journals and bearings making love and grenade a motor. Remember that all moving parts inside the motor aren't ball bearing and are journal bearings and require oil to separate the surfaces from contacting.
    • Yeah I noticed this just now. No doubt she will be running smoother next start😂🤣😂
    • ENR34 manual transmission transfer cases are 33100-23U00 which is shared with all of the R32/R33 GT-Rs and GTS-4s. And the C34 Stagea. Do not bother with automatics, that is a huge effort to swap and the car will be worse for it. And an automatic transfer case does not have the right housing for the shifter which comes out the back of the transmission and goes through the transfer case. I already posted my response on reddit but if you didn't see it there here it is: You have almost certainly damaged the transfer case, the only question is how badly. Nobody can tell you how bad without more information. If you have a giant hole in the transfer case pissing out all the transfer case fluid then you need a new one. If it's not that bad then the only question is whether you burned up the clutches. Drain the transfer case oil and inspect for metal on the drain plug magnet. Small black filings are normal. Big chunks of metal or a ton of black fuzzies not so much. Fluid should be nice and red. Any other color isn't great. If the color is reasonably red and there's not a bunch of clutch material discoloring it or anything like that you probably got away with insubstantial excess wear not worth trying to fix. If you have to rebuild or replace the transfer case keep in mind you have to pull the transmission to get it off.
    • As promised………… the first start. Rough and a few bugs to work out. Still she lives att.1cnTUvrWxiOZUFbg0S43m1VFUdDhxGBq3UU53bvtkww.mp4
    • Can I suggest a 15W50 oil is too heavy. Its a brand new engine - you should be able to run something like a 10W30. Shove some steel wool into your catch can  - more technically "oil/air separator" - so that the oil vapour has something to condense on.
×
×
  • Create New...