Jump to content
SAU Community

Recommended Posts

hey guys

I recently installed a set of 6" MTX 6001 (90RMS) speakers in the rear parcel shelf. They are being run off a kicker amp so i believe they have enough power, but if i start to turn up the volume it sounds like there is interferance with the signal as if i was listening to a radio station that wasnt correctly tuned in? I tried playing with the treb, bass and gain on the headunit and amp but with no luck. Any one had this drama or have any suggestions?

cheers luke

Link to comment
https://www.sau.com.au/forums/topic/131909-distortioninterference-prob-r33/
Share on other sites

Sounds like you are having the famous "alternator whine" problem which is experienced by many a Skyline owner. Does this "interference" increase in loudness with the revs of your engine?

Not really its only when i trun up the volume that i start to hear the interference. I did however here the engine idle come over the speakers when i was sitting at the lights. But its not the sort of distortion that you would associate with crappy speakers that are being put to the limit but like i stated, more like when the radio station isnt tuned in properly.

Ah yeah. I have both. The hazy static noise went away when I turned my gains down on the amp though.

The whine is still there, and there's just about nothing I can do to get rid of it.

I found a blown ground wire for the RCA's in my head unit, repaired that, tested with a multimeter, reinstalled, but it's still there. If I unplug the front set of RCA's, it goes away. Changed cables, swapped front and rear, changed amp. It won't go. Pretty sure it's my headunit that's at fault.

So. Turn down your gain. ALL THE WAY down. Then crank your headunit and see if the static is there.

Yeah, from what i've read, if everything else has been done correctly, then the only other thing that causes the static and whine is a bad RCA earth.

Either you've killed the earth in the amp, or in the HU. It's hard to find out without borrowing someone else's stuff.

I'm quite sure my HU is the problem. It had a burt track in the HU, and the amp has changed to a different new unit.

Yeah, from what i've read, if everything else has been done correctly, then the only other thing that causes the static and whine is a bad RCA earth.

Either you've killed the earth in the amp, or in the HU. It's hard to find out without borrowing someone else's stuff.

I'm quite sure my HU is the problem. It had a burt track in the HU, and the amp has changed to a different new unit.

yeh im going to borrow a amp this weekend and see if it fixes the prob, and ill write up my results

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What will you do when the Minister of War and Finance says the intake noises are too loud?
    • Will the clear coat dissolve the ink tho?? I thought about clear vinyl tape too. Thinking what to do haha. The one I have now is cracked in 1 spot, otherwise mint. Plus the MINES one is much thicker plastic material so its not flimsy at all.
    • No. Go a different colour, and just trim it at an edge line. Even manufacturers do different panels different colours etc.
    • I see no real downsides to ITB's, apart from the initial cost of my drive in drive out lifestyle, the "upsides" is they sound cool and would add lots of smiles I am willing to pay to play for the extra smiles I've spent the morning googling and youtubing the BBR ITB's, a "little" extra power and throttle response, but alot more dort, and really, I'm only really in it for the dort Who knows, after all this money is spent I might even make 150kwatw....LOL  
    • With my block out to get honed, I'm just prepping all my auxiliary components in my mean time. I took my oil pump apart to inspect and repack it with assembly lube and either haven't noticed this in the past or found my answer and can't remember. What exactly is the regulator washer that the manual mentions replacing? I don't have one and from the manual it seems to seal the regulator plug to the housing but I can't see it on any pictures of new pumps either. Can anyone fill me in? I'm presuming this was phased out as I also can't find a replacement part in epc.    Image of a new pump. Can't see a washer there either.
×
×
  • Create New...