Jump to content
SAU Community

Recommended Posts

theres always a bit of noise, when moving the steering wheel it is loud, when at full lock it is louder.

This happens when the car is moving or not. I'm pretty sure its the power steering pump, can ya fix em or do i have to get another one ?

In the Information and technology industry the first thing a tek will as is for you to explain what it is and is not doing in more detail. I see no resin why this shouldn’t be the case here.

Please what kind of noise is it making?

Squealing, squeaking, grinding or another sound I have not covered here or maybe a few of the sounds all together?

  • 3 months later...
Yeah it was just low fluid level. Very embarassing post !!!

Good to see it was just fluid, unusual that the HICAS light never came on???

Was going to say if it was the pump try make a distinguishing mark on the pump so u can tell if it is a new pump or just your one recoed, seen it done before charging for a new pump & the old pump has just had a seal kit put through it.

Give u a idea your looking at around $50 for a seal kit & about 1/2 hr to a hour to pull the pump down & rebuild it, so say $150 - $200 all done, with new pump say around $450 - $500...

Some thing to keep in mind... :P

how about this?

the hose coming from the bottom of the power steering fluid reservoir is always wet. i noticed this on alot of r33's. funny thing is the fluid level has never dropped. what's that about?

how about this?

the hose coming from the bottom of the power steering fluid reservoir is always wet. i noticed this on alot of r33's. funny thing is the fluid level has never dropped. what's that about?

Had the same thing with my old 33, fluid would leak out the bottom hose and fill up the surrounding rubber sleeve. Ended up just getting new clamps and she was all sweet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
    • Not great at getting the camera out fast enough for cars driving. Even in traffic. S15 is in front of the kei truck.
×
×
  • Create New...