Jump to content
SAU Community

What Fuel Do Skylines Love?


brizzi
 Share

Recommended Posts

  • Replies 69
  • Created
  • Last Reply

Top Posters In This Topic

well guys i have a tock standard 260rs with a dtop in replacement K7N and a full 3" echaust fitted.

i ran with a few 98 rons and founf mobil to be the most powerful , bp smoother and sheel the worse of the lot. ALthough i miced once optimax with extreme once and theres a lot of difference only 10 ltrs to the tank i added with the extreme.

Since Sk said and proved that theres no problem running on extreme then how about running on United? Anubody test it long term @ 10 or 15% ethanol? Cos it sounds very cheap. Ectreme costs about 1.59+ i think. Im very tempted to try the United one.

heres is the link to see where its available in whole Oz

http://www.unitedpetroleum.com.au/distribu...8-locations.asp

Edited by stasis
Link to comment
Share on other sites

I just had a fiddle with Uniteds Boost98 E10 pulp.

Not all that happy with it to be honest. knock levels are down and it allows more timing to be dialed in but it just doesn't seem to have the same top end as the usual BP 98.

Maybe its going a tad lean but if that were the case I would expect it to detonate which its not. hrmm

Best not too fiddle as its strange, off for a power run it goes.

Link to comment
Share on other sites

Really doesn't bother me to be honest. I don't plan on running the united boost98.

Optimax Extreme I believe will be fine.

I have heard reported in the media issues with ethanol and engine corrosion and its effect on metal parts. What steps are you taking to protect my engine and its components?

The issues you have heard about relate to a situation in 2003 when some retailers were selling fuel products with more than 20% ethanol blend without sufficient disclosure to customers. Shell was not involved in this practice and took active steps at the time to promote that our fuel did not contain ethanol. It has now been shown through extensive testing and research that a maximum 10% ethanol content is suitable for many cars which is why the Federal Government has set a maximum 10% ethanol content in Australian fuel. Shell has determined that a formulation of 5% ethanol optimises Shell Optimax Extreme (the same level that Governments in Europe are encouraging in their specification). All ethanol used in Shell fuel contains a suitable corrosion inhibitor.

I will be ripping out the fuel pump (shows up there first) 3 months after I start using the fuel to ensure there is no corrosion. If not then another 3months and if not then another.

Link to comment
Share on other sites

I tried United Boost 98, 3 days ago and although it drives smoother (ie when revving at 4k rpm it feels like 3k rpm), it massively loses power ( on a BNR32), I mean its noticeable!!.

One thing i noticed beacause i overfilled with boost, that it left a yellowish oily trail, which went like glucose overnite, and couldnt be cleaned with water, but with soap.

Link to comment
Share on other sites

I too noticed Boost98 was smoother and appeared to have more part throttle acceleration, however top end suffered. Do remember to make use of this fuel the car needs to be tuned to suit as it leans the car out.

I richened up mine by 1 point which should have brought it back to 12:1 and dialed in more ign until I saw det but it still just didn't feel the same in the top end as the origional setup with BP 98.

So for me.. Its bp98 until Optimax Extreme heads my way.

I must also mention my external bosch fuel pump in hot weather usually develops a loud buzzing fuel sucking type noise. It can only be heard on the out side of the car.

Well... Since I dropped this Boost98 stuff in even in cold weather it has constantly had this noise. I used the Boost98 up, dropped in BP 98 and instantly the Bosch pump was quiet and has stayed quiet all the way home.

Interesting.

Link to comment
Share on other sites

I too noticed Boost98 was smoother and appeared to have more part throttle acceleration, however top end suffered. Do remember to make use of this fuel the car needs to be tuned to suit as it leans the car out.

I richened up mine by 1 point which should have brought it back to 12:1 and dialed in more ign until I saw det but it still just didn't feel the same in the top end as the origional setup with BP 98.

So for me.. Its bp98 until Optimax Extreme heads my way.

I must also mention my external bosch fuel pump in hot weather usually develops a loud buzzing fuel sucking type noise. It can only be heard on the out side of the car.

Well... Since I dropped this Boost98 stuff in even in cold weather it has constantly had this noise. I used the Boost98 up, dropped in BP 98 and instantly the Bosch pump was quiet and has stayed quiet all the way home.

Interesting.

I have use optimax extreme and its 10 cents more expensive than optimax itself. Long term in terms of affordability its very expensive.

That why i was so interested in the United boost 98 get it tuned to match it and it will save long run. Thats just my theory anyway. But optimax xtreme is damn expensive.

Link to comment
Share on other sites

I have use optimax extreme and its 10 cents more expensive than optimax itself. Long term in terms of affordability its very expensive.

That why i was so interested in the United boost 98 get it tuned to match it and it will save long run. Thats just my theory anyway. But optimax xtreme is damn expensive.

I'm just not sure I can put up with the fuel pump sound that the BOOST98 causes. :)

I've now got BP98 in it and the fuel pump (external Bosch) has gone silent again.

Its a strange finding but most likely due to myself not throwing the car on the dyno, richening up the afr and dialing more ign. in on the usual boost level saw no noticable improvement. However simply dialing up the boost did. There was no knock on Boost98 and the car felt strong. Drop BP98 back in to it and it began detonating.

So Boost98 does appear to have an advantage over the BP98. It simply needs to be tuned to suit, there is no point even trying to fiddle myself on the street without a wideband.

But yer.. Not sure I could put up with the fuel pump noise from Boost98. :laugh:

Link to comment
Share on other sites

I'm just not sure I can put up with the fuel pump sound that the BOOST98 causes. :)

I've now got BP98 in it and the fuel pump (external Bosch) has gone silent again.

Its a strange finding but most likely due to myself not throwing the car on the dyno, richening up the afr and dialing more ign. in on the usual boost level saw no noticable improvement. However simply dialing up the boost did. There was no knock on Boost98 and the car felt strong. Drop BP98 back in to it and it began detonating.

So Boost98 does appear to have an advantage over the BP98. It simply needs to be tuned to suit, there is no point even trying to fiddle myself on the street without a wideband.

But yer.. Not sure I could put up with the fuel pump noise from Boost98. :laugh:

Other than your fuel pump noise no other problems? Does anybody used boost 98 before on a long term? Can we set 2 different settings with the power Fc using the hand controller than? Switching to different mao when using different fuels.

Link to comment
Share on other sites

^ OK well if you're gonna be that specific about fuels, I'd call that semi-PULP fuel if i was being pedantic.

But either way, the original statement made by Rosie_1008 is still wrong according to SydneyKid's knowledge - throughout the thread he has informed us of the different fuel companies who share their 98RON fuels, and which fuel comes from where and whos refinery.

Link to comment
Share on other sites

the only problem is that apparantly ethanol can bond to H20 - thats why there was a stink about it when it was first being used coz obviously water and pistons dont mix.

however i think its unlikely to actually get enough water into your engine to do instant damage but i think the whole point is that it "can" do damage over time... who knows if it actually does... i mean most of us use high flow air filters that prolly let in just as much crap and water vapour anyway.

dude why do people put water injection systems in there car to help with inlet temperetures.... an awfull lot of supercharged cars an now quite a few turbo'ed run a water injection system on the pressure side cant see its gonna hurt the pistons when you have a exploding fireball next to it... gonna dissapate preety quick

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • to have this type of adjustment possible with a curve as I wish, what budget (engine) should be planned?  
    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
×
×
  • Create New...