Jump to content
SAU Community

Recommended Posts

for my consult lcd, hoping to get L/100KM reading on it, so need to know all the common nissan injector sizes for the injector setup. this will basically be the size of injectors people are to chose from when setting it up:

135cc (CG10DE/CG13DE)?

148cc (CG10DE/CG13DE)?

185cc (GA16DE)?

200cc (GA16DE)?

250cc (S13/N14 SR20DE)

260cc (S13 CA18DE)

270cc (S14/S15 SR20DE, RB20DET)

370cc (CA18DET, S13 SR20DET, RB25DET, VG30DETT, AUS S15 SR20DET Purple)

380cc (S14 SR20DET)

440cc (RB26DETT)

480cc (JAP S15 SR20DET Maroon)

upgrades: 550, 600,660,720,740,850

question: are there any values that may be used ive missed? any wrong?

Edited by NewKleer
Link to comment
https://www.sau.com.au/forums/topic/132566-nissan-engine-injector-sizes/
Share on other sites

thanks, updated. not sure yet if ill just get people to enter in their car, or just inj cc size. or maybe car then let them edit inj cc size

Edited by NewKleer

btw thanks for everyone's help, im just going to require user to specify the size rather than try and provide a list of all possible injectors for them to choose from (which itself would take a lot of memory up on the device also). but this should be a good reference for anyone who's not quite sure

JDM S15 injectors are rated at 480 but many have had them flow tested and often 440 pulls em up hense the confussion. There is also conflicts between whether all S15 manuals run 480cc injectors or just the JDM spec ones. The simplist way to tell is

maroon top = 480cc, purple top = 370cc.

cheers

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...