Jump to content
SAU Community

Recommended Posts

I have been having a problem with flat spotting.

I run NGK plugs with a heat range of 7 and on cold canberra winter mornings they flat spot until I get some boost over them, then they are fine.

I have tried using a heat range of 6 and they dont flat spot in the morning but they do flat spot with higher boost levels and they also knock a little higher (I am guessing pre-ignition)...So I am sticking with the 7's gapped at .6

Anyway could this flat spotting be the reason why my catch can has fuel in it? The catch can does not feedback into the inlet and I have blocked the PCV valve.

Also does a smaller gap rob you of any power?

Any ideas on the matter would be great

thanks in advance.

Edited by GunMetalR33
Link to comment
https://www.sau.com.au/forums/topic/133164-petrol-in-the-catch-can/
Share on other sites

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

too much knocking or something else has caused your rings to lose their tension and petrol is bypassing them and its going round with the oil.

That's what I figured but there is no oil in the catch can and the compression in all 6 cylinders is within 10% of each other. If the rings were worn it would show on the compression test and I would think there would be oil in the catch can???

yes, smaller gap will rob you of power. why are you gapping the plugs so tight? 0.6mm gap is tiny. you should be somewhere between 0.8mm and 1.0mm.

edit: I have NFI how you are getting fuel in your catch can, but it's not good. 2. are you sure it's fuel?

well the petrol thing isnt...we had a similar problem in our race rb25det except the rings were shagged and the compression was down, regardless if they were all down the same or within a certain amount it was still happening, petrol in the catch can, not just oil.

I cant see another way of it bypassing and getting into the catch can.

With such a smal gap, you are probably not burning the fuel properly. Unburnt fuel is then being dissolved in the oil on the cylinder walls and taken down into the sump.

Open the gap. (usinga really small gap is only masking the real problem)

compresion test with fuel washing away oil on the bore is not a acurate test, remoove the plugs + the fuel pump relay, crank the motor over and let all excess fuel out, then re oil the bore and potentialy change the engine all oil together, lightly lube the bores with small amounts of oil then allow the car to sit for a lil while then perform another compression test..

Thanks for all the replies.

To answer a few questions:

1)Yes I am sure its fuel, very little oil, only enough to slightly discolour the fuel.

2)I run .6 of gap to stop flat spotting. Anymore gap and it flat spots. However I have removed a big restriction in my zuast since gapping the plugs down so I might gap them out and see what happens.

3)The max compression in was 150 psi in one cyclinder with the rest being within 10%. Most above 140 psi.

Could it be a head gasket problem? I am running 19 psi :P (yea forgot to mention that)

PS => if the rings are worn which I am sure they are (at least a little) how long will they last. Will they continue to wear or will they just sh*t them selves one day :{

Also how much for a re-build with forgies if I take the engine out and deliver it??? Just after a ball park figure. I am tring to save for a house :{

having spoken with Timmy and hearing the power you are putting out with standard internals it would not surprise that it is starting to die. Standard internals + the power you are making = upcoming rebuild... sorry to say it :P

oh also forgot to mention alot of the SAU Canberra and even Sydney guys who have had rebuilds have gone and seen Greg @ proengines. Maybe give him a call he may be able to offer some advice. http://www.proengines.com.au/

having spoken with Timmy and hearing the power you are putting out with standard internals it would not surprise that it is starting to die. Standard internals + the power you are making = upcoming rebuild... sorry to say it :/

oh also forgot to mention alot of the SAU Canberra and even Sydney guys who have had rebuilds have gone and seen Greg @ proengines. Maybe give him a call he may be able to offer some advice. http://www.proengines.com.au/

Yea, a lot of power to timmy is 140rwkw or what ever his old beamer used to make :mage: I have about 260 now and plenty of guys run that sort of power for a while. But I think you are right, engine is starting to get a little tired now :P

if hes only running the 246rwkw then stock internals are fine. As for 20psi and fuel in catch can also its missing.... What do all the plugs look like? If for some reason there is fuel in the oil look at the bigger picture your oil is f**ked now its thined out which will damage your bores.

I cant see how fuel gets into the oil, ie its sprayed into a chamber compressed then detenated and push out the exhaust valves.

You must have some bad underling problem eg craked head, head gasket to oil, valve guides, oil rings.

... I am running 19 psi :P (yea forgot to mention that)
There's the reason for your flatspot - the engine probably can't ingest air at 19 psi. Back the boost off a bit - I reckon 1 bar is more than enough.
if hes only running the 246rwkw then stock internals are fine. As for 20psi and fuel in catch can also its missing.... What do all the plugs look like? If for some reason there is fuel in the oil look at the bigger picture your oil is f**ked now its thined out which will damage your bores.

I cant see how fuel gets into the oil, ie its sprayed into a chamber compressed then detenated and push out the exhaust valves.

You must have some bad underling problem eg craked head, head gasket to oil, valve guides, oil rings.

I only just replaced the oil 1 month ago, I had 245rwkw before I shaved down a restricting turbo spacer to the correct diameter. Car is a lot faster now... I estimate about 260rwkw...

Plugs look good, a nice bronzy like colour but not too light...

So you reakon I should change the oil again? This motul stuff aint cheap :P

There's the reason for your flatspot - the engine probably can't ingest air at 19 psi. Back the boost off a bit - I reckon 1 bar is more than enough.

Yea, I will re-grap the plugs to .75 then wind down the boost till she stops flat spotting. Does anyone know the coversion between psi and bar, as in what is 17psi in bar?

If this is the case...maybe see if you can borrow a set of splitfires for a day and gap your plugs to .8. I still had major issues with those bosch coil packs (if you're still running them?) and haven't had a hint of a miss since I got the Splitfires

With such a smal gap, you are probably not burning the fuel properly. Unburnt fuel is then being dissolved in the oil on the cylinder walls and taken down into the sump.

Open the gap. (usinga really small gap is only masking the real problem)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yuck. But it's kinda the same principle, moving timing around to make car run bad but sound good.... I went for a more spirited tuning drive to iron out a few things. Car no longer stalls, and it loved to dip RPM low when you clutch in. After tuning this (and the 4-5 tables that HPTuners/LS1 OEM ECU wants for idle air correction) it's now behaving somewhat normal. All expected because there's a new TB, new Intake manifold and that new TB which is 102mm vs 78... has an entirely different IAC passage which is smaller because ????? Unfortunately at this point I went to make further fine tuning changes to avoid it flaring up, you know... _tuning_ the HPTuners dongle died. Well to be more accurate - The USB cable died in a fashion that anyone who has ever charged a phone will recognize. After the app demanding I resync it 50 or so times (which all 'succeeded' but all failed) the device does not want to sync and I've logged a ticket with support to see if it's fixable. US Support said it was a 'storage issue' but after removing the SD card inside it and formatting it/fixing it the issue does persist. Unfortunately usually the fix is "Turn in your old dongle and pay $700 for the upgraded one" it's cheaper because I get some free licence credits I unfortunately don't need. However I'm 10 minutes down the road from HP Tuners AUS/VCM so at least I won't need to post it, and logged a new ticket for support over here. Definitely drives different. My SOTP dyno believes it's probably making 310-320kw instead of the 280 before.  It scrambles for traction a little now whereas it previously different. It drives like a bigger cam car up top even though the cam is smaller, likely due to the cam not being advanced 6 degrees. The timing is deliberately low and the fuel is very rich so who knows if this will improve on the dyno. It may, imperceptably. Also funny is removing the pineapples definitely makes the car squat more and axle tramp less. So this behavior of having more top end, squatting more, and scrabbling for traction more makes me think = more power. But I could have just been sitting on the threshold of that kind of behavior before. Time will tell if my butt dyno is calibrated right. I need the exhaust leaks fixed before dyno tune for obvious AFR related reasons - I repositioned the pipes but I'm not confident it's fully sealed even if it is better. At least the car does drive around while I cannot tweak/tune it for now. And I have aircon again. medium success!
    • Don't use that manifold. Please don't use that manifold. Sunk cost fallacy is not worth the later pain. None of these will be relevant to the change that will come from the different turbo and manifold. As in, the effect of the exhaust will be nil, regardless of what else is changed. And all the cam and fuel system stuff is not changing either way, so has no effect. The turbo and manifold (and to a small extent the wastegate)....big change.
    • Just wanted to say thank you for your input   my man (lead mechanic by trade) and I have done a heap of work as you can imagine just to make the hot side work with the dump pipe, stupid massive intake on turbo, trying to get the waste gate on was not fun.  I’m kinda getting to the point where I don’t know if I try and make this work and not throw all this cash and time away or do I scrap the lot and start again? the Apexi I’ve got was tuned for a few slight differences:   Tomei pon cams (mine are stock neo) Turbo smart 38mm external waste gate (mines 45mm replumbed) with stainless screamer pipe  3inch turbo back exhaust with high flow cat Sard 800cc top feed injectors Sard adjustable fuel pressure reg    
    • Out here E90s are the cheapest way into a sporty-ish car because everyone knows just how expensive the repairs can get. 8-10k USD for an automatic 335i. 
×
×
  • Create New...