Jump to content
SAU Community

Recommended Posts

Guest INASNT
Originally posted by ice180

1992 180sx

301 rwkw same dyno as SAU

12.3 at 100mph at Heathcote, backed off past half track due to car getting very wayward.

1.7 60ft and 7.6 sec at 90mph to half track.

will be back when gearbox is fixed and with front runners.

damn ice i thought u would have got better than that!!!

were u driving or sum1 else?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

thks dude as I said had to back off at half track I couldn't control it as it was getting very wayward, full throttle was probably less than 50% of the run... We will be back with proper front runners std front suspension - it was way to low, and the gearbox input and output shafts re done... If you look at the time and speed to half track plus the 60ft indications are there that it should be good for a ten, plus the terminal speed was very low for a 12.3 which indicates good acceleration until I backed off.... I'd rather take the car home it one piece than put it into the wall...

Guest INASNT
Originally posted by ice180

thks dude as I said had to back off at half track I couldn't control it as it was getting very wayward, full throttle was probably less than 50% of the run... We will be back with proper front runners std front suspension - it was way to low, and the gearbox input and output shafts re done...   If you look at the time and speed to half track plus the 60ft indications are there that it should be good for a ten, plus the terminal speed was very low for a 12.3 which indicates good acceleration until I backed off....  I'd rather take the car home it one piece than put it into the wall...

funny thing is that after the dyno day when they gave your 180 a fang around bayswater they got upto 100mph 2!!:burnout:

CAR:

SR20DET S13

MODS:

T28

Blitz Pod Filter

Custom Dump, Front Pipe (3.5")

High Flow Cat

HKS Hiper Exhaust

Turbosmart Type 1 @ .8 Bar

HKS BOV

16" Wheels on 225/50 Street Tyres

DYNO RESULT:

21/06/02 140.7 rwhp on SST Dyno Dynamics Dyno (had split vacuum hose)

06/02/02 178.0 rwhp same Dyno without BOV

QUARTER MILE TIME:

13.616 @ 102.27 mph (2.28 sec 60")

Just fitted FMIC, having major boost spikes, and hitting AFM cuts hmmm :D

Only had the BOV put on a couple of days before the last dyno. The BOV is fine, it was just that one of the old vacuum hose got hard and split severely. Full boost came on late and didn't hold full boost for very long, peaked at 12psi then dropped to 10psi. The 13.6 sec run was done the weekend after the last dyno, had already replaced the split hose.

FORD CAPRI TURBO

BIGGER INTERCOOLER

HI-FLOWED STD TURBO 2MM BIGGER COMP WHEEL

3" EXHAUST

UNIFILTER POD

CHIPTORQUE CHIP

121KW@TYRES

14.141@98.92MPH

0.607 REACTION

2.32 60FT

6.096 330FT

9.187 660FT

STUPID ME CHANGED INTO 5TH B4 THE FINISH

PREVIOUS RUN DID 99.8MPH/14.3/2.4 60FT

18/08/01 @ WILLOWBANK

CAR HAS OPEN CENTRE BUT I USED SOFT COMPOUND RETREADS

STILL SPUN SINGLE WHEEL BADLY

Here is mine.....

CAR:

R32 GTR

MODS:

rebuilt RB26DETT all new internals

1mm oversized forged pistons

port polished head, steel gaskets etc

oil restrictor to head

sump baffle

Apexi PFC

700cc injectors

fuel pressue regulator

Apexi Hybrid intercooler

adj cam gears

Nizmo/Garrett N1 BB Turbo's

HKS Dump pipes

custom made tuned length twin 2.25 inch engine pipes

into 3.5inch collecter

HKS Hiper exhaust 3.75inch (95mm)

OS Giken twin plate clutch with lightened flywheel

whiteline suspension kit

1.15 Bar Boost (at moment will take upto 1.7bar, injector cycle

at 64% at this boost)

DYNO RESULT:

268 Rear Wheel Kilowatts (Hills motorsport)

same engine at 10psi (not tuned, but dynoed at 195rwkw)

on g-tech 0-100kph 4.73 and 1/4 12.95 two people full tank)

QUARTER MILE TIME:

Not formally run yet

Originally posted by ONARUN

:confused:  

what gives?

not enough traction? no suspension?

suspension stock and traction was no good that day.

the 14.10 was during the day while the 14.01 was at night, i was having heat problems with the cooler so let her be after only afew runs.

hrmm..

Thats an interesting figure skyzeer33.

As you can see by my sig i'm getting 156rwkw with boost dropping to around 11-12psi.

156rwkw = around 210rwhp.

So with the less weight of the R32-T I should be pulling in to the 13's.

Well maybe thats why I only just beat Andy's 33 GTR with a launch some where around 5000-6000rpm. :shake:

gt2530 turbo in a few weeks so it should get interesting then :D

I'll post my 1/4 run once I get the turbo.

Yes..

I am getting an adapter made up.

:)

And the Dump pipe also has to be modified which isn't to much of a hassle.

Should be in a few weeks if all goes well.

Thats the partial reason why I didn't go on the cruise this weekend.

Too much thrashing on a std turbo running 1 bar = Tow Home.

Which = Car off the road for 3 weeks = less money for new turbo = no turbo until probably 4 weeks.

= BAD

I'm going to get the ECU tuned from Tilbrooks so I'm really interested in the extra down low off boost power that they can tune in.

I'll see if i can get a dyno run from like 1000rpm or somthing to show the extra power down low. (BEfore and After)

  • 1 year later...
OK guys,

CAR:  

R32 GTR

MODS:  

Trust Airinx Filter Kit

Trust MX front pipes (2 x 75mm into 1 x 80mm)

Hi Flow 3"(80mm) Cat

Buddy Club Racing Spec III Exhaust (89.1mm through)

HKS Slide Cam Pulleys (cam gears) - IN and EX

Custom Bleed Valve

1.1 Bar Boost

DYNO RESULT:  

240 Rear Wheel Kilowatts on RacePace Dyno Dynamics Dyno

QUARTER MILE TIME:  

11.573 @ 117.89 mph (1.712 sec sixty foot)

Shaun.

Guys, I know this is old thread, but is the above "posted by" Shaun AKA HiRisk for real?? 11.5 Qtry Mile @ 240rwkw, on stock turbo's?

I haven't run a qtr time but my car reads like this..

CAR:

R33 GTR Series 3

MODS:

HKS Pods

Front Pipes (2 x 50mm into 1 x 75mm)

Cat Back "I think 80mm"

Stock Cat

Apexi Power FC

Cam Gears

Turbosmart Bleed Valve @15psi Boost

DYNO RESULT:

270 Rear Wheel Kilowatts on RacePace Dyno Dynamics Dyno

QUARTER MILE TIME:

Unknown??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm seeing torque specs all over the place for the OUTER tie rod, but none for the INNER tie rod, where it connects to the steering rack. Even in videos, people are just tightening em up as much as they can with a wrench and that's it. Anything tightened down without torque makes me nervous. Anyone know what the spec is for it?
    • Hope you had a great time here in our tiny country.   The JDM scene we have here is quite small, it's mostly BMW, Volkswagen with burble tunes haha. But the few JDM cars we do have in the scene are pretty nice. Some of my friends drive cool s14's too. Both built engines, red one makes abt 500, blue one abt 400 i think?
    • Ye good idea , would have never thought of something like that. Might aswell do it to every pulley and the balancer while I’m there 
    • Use an LS1 or similar, via kit like Frenchy's. But.... It's probably not the alternator. It sounds like belt squeal, which would be because the pulleys are glazed. Rub every groove on the pulleys with 120 grit paper. Report back. Oh, and new belts afterwards too. The old new ones will be shitted up already.
    • Hello all I have 2 r34 sedans , one turbo one na, only recently aquired the na 34.  Man what is with these things.... My turbo 34 started sounding like a super charger, it was screaming at anything above 4000rpm , I took the alternator apart and replaced the front bearing which is the only one I think you can access and it did not fix the issue so presumably the bearing in the rear of the alternator is gone. ( diagnosed it was the alternator by taking off the aux belts one by one to figure out which pulley or bearing it was )  My friend gave me one he had lying around, Installed it , it did not squeal for maybe 500kms and now its started to squeal again briefly on startup  Recently got an na r34 and I replaced the timing belt, water pump + all the auxillirary belts. Runs amazing but it suddenly developed the same squeaking problem but significantly worse, Ive had my neighbour come down screaming at me because it was waking her up everytime I moved the car. It takes a good 2 minutes before it quietens down.  Im yet to diagnose where its coming from but im fairly sure its coming from the alternator aswell. My question isnt about how to fix it but rather where can you get a new alternator for an rb25 neo??? Ive searched everywhere but I havent been able to find a direct fit oem type replacement thats not genuine. All the automotive stores sell an oex one - BXA035 - which I picked up for cheap through a friend with staff discount , got it home only to find the connector is completelty different.... As far as im aware bxa035 is for rb20/30's and after a bit of figuring out the bxa035 has an ev14 type connector, which is tiny compared to the rb25 connector. I actually had an ev14 connector lying around which I was considering just replacing the bigger plug with to get the alternator working but the bxa035 is rated for 70amp vs the rb25 alternators are 90amp ( or so ive been told ? ) That paired along with the fact im about to install an amp + sub in the back and I have the stock sized small battery Im not sure itll do the job unless anyone has another opinion?  I know and have seen all the websites selling the ls1 alternator conversion kit but I am not going down that route, nor do I have the money to. Hopefully I can figure out how to get 2 brand new alternators for both cars. I would buy second hand which there seems to be many of but considering how common this seems to be im sure If I installed a second hand one it would start squealing in no time  Or even better if anyone knows how to fix the issue directly with the alternator itself... Any input appreciated Thank you     Link for bxa035 connector picture
×
×
  • Create New...