Jump to content
SAU Community

Recommended Posts

Ok so

so far the car has got all the supporting mods

Walbro Gss432 pump

adjustable fuel pressure regulator

full 3" exhaust with dump pipe

HKS pod and intake

boost regulator

SAFC II

FMIC

New 02 sensor

New ECU temp sensor

I am running 7psi at the moment, and when i got o tune the SAFC II i want to run 12psi and no more, less if i can get away with it.

The tunner told me that 160rwKw is basically what is actually posible, i have no idea why, that is only a 40kw increase over stock.

Now basicaly intake and exhaust is a good 10kW, pod 5kW, 5psi boost 40kW, remap, about 10kW so that should be a total gain of about 65kw. Now stock at the RW is about 120-130kW so that should be about 180-190rwKw in total

So what the helll is he on about.

Can people post up their output figures with the mods. I am not too sure if the tuner can be trusted but that is the only one poeple have recomended.

What sourght of power figures should i be looking at, and what do i tell the tuner to do, ie fuel air rations and recomendations to my tune.

HELP PLEASE, i want to get this right, as i am on a budget. Thanks.

SILLY ME. she's a 1995 R33 series 1.5. Opppsa

Edited by WogsRus
Link to comment
https://www.sau.com.au/forums/topic/134905-car-booked-in-for-a-tune-safc-ii/
Share on other sites

1.What car is this for btw? R32 Or R33 Or R34?

2. How much power is the car making now prior to installing SAFC + tuning?

3. What turbo are you running? stock?

4. If its a r33 with the mods you have listed on stock turbo i personally believe you'll be getting between 170-190rwkw as well. If its an r32 then 160rwkw is my guess.

my 2cents

remember auto's dont read aswell on dyno's as manuals do,

i was told by my tuner,he said it reads a little higher down low

(something to do with the torque) and read low up top.

89' rb20det r33 turbo+zorst & SAFC1 automatic = 165rwkw

12psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...