Jump to content
SAU Community

Recommended Posts

Theres lots of posts about spark plugs on here but ive got a question.. :D

R33 gtst usual mods standard turbo..

Re-moved "iridium nismo 8" spark plugs from car (god knows what these are? 0.8 gap?)

Put in NGK Iridium BKR5EIX-11, gapped to 0.8 (i know you're not supposed to gap iridiums).

I wanted to put in BKR6EIX, but id allready bought the BKR5EIX.

Running with the BKR5EIX 's the engine wasnt even coming onto boost it was just pinging and spluttering everywhere.. with low down torque not really there either..

I put the Old iridium nismo 8 plugs back in and all is now good and back to normal..

So im guessing the Iridium BKR5EIX (5 heat rating) is too hotter a plug?

I know i should have the 6 heat range, BKR6EIX, for the kind of mods i have, but would the 5 really do this kind of thing to the performance of my 33?

Any feedback would be great.

Looks like ive just wasted $100 on the damn wrong heat range sprakies.. :( , Dumbass.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/
Share on other sites

Theres lots of posts about spark plugs on here but ive got a question.. :nuke:

R33 gtst usual mods standard turbo..

Re-moved "iridium nismo 8" spark plugs from car (god knows what these are? 0.8 gap?)

Put in NGK Iridium BKR5EIX-11, gapped to 0.8 (i know you're not supposed to gap iridiums).

I wanted to put in BKR6EIX, but id allready bought the BKR5EIX.

Running with the BKR5EIX 's the engine wasnt even coming onto boost it was just pinging and spluttering everywhere.. with low down torque not really there either..

I put the Old iridium nismo 8 plugs back in and all is now good and back to normal..

So im guessing the Iridium BKR5EIX (5 heat rating) is too hotter a plug?

I know i should have the 6 heat range, BKR6EIX, for the kind of mods i have, but would the 5 really do this kind of thing to the performance of my 33?

Any feedback would be great.

Looks like ive just wasted $100 on the damn wrong heat range sprakies.. :) , Dumbass.

Yah think you have got yourself some hot plugs, put it ip in ebay and sell at half the cost. At least you can recover something back.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2517133
Share on other sites

you can't go past the plugs with the code BCPR6ES. they are only copper and are about $3 each (better than about $20 each for iridiums). i've had mine in for about 10,000kms at between 12 and 14psi and they haven't missed a beat. it had iridiums in there and they were dead after 20,000ks. i'm going to change them again at the next oil change (at $24 a set, why not)

but a guy i know put platinum plugs in (heat range 5) and it pings like a bitch, and pops and farts. he took me for a spin in it last night, but he wouldn't listen when i told him his plugs where wrong (1 of those know-it-all types).

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522759
Share on other sites

you can't go past the plugs with the code BCPR6ES. they are only copper and are about $3 each (better than about $20 each for iridiums). i've had mine in for about 10,000kms at between 12 and 14psi and they haven't missed a beat. it had iridiums in there and they were dead after 20,000ks. i'm going to change them again at the next oil change (at $24 a set, why not)

but a guy i know put platinum plugs in (heat range 5) and it pings like a bitch, and pops and farts. he took me for a spin in it last night, but he wouldn't listen when i told him his plugs where wrong (1 of those know-it-all types).

Sometime cheap is not necessary bad and expensive is not necessary good. The key is to choose the correct form, fit and function that cater to your engine. The BCP6ES are without the V groove, choose the BKR6E-11 (gap down when necessary) which cost around there too.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522802
Share on other sites

It all depends on the mods you have.

a mildly modded car shouldn't have major issues running a 5 as they are the stock replacement plug.

A 6 heat range plug is a good move with more boost up to about 1.1bar/16psi. bcpr6es/bkr6es is .8 copper out of the box, bcpr6e or bk.. is the v groove option.

A 7 over that up to low 20psi

I'd start with a 6 bcpr6es as they are cheap enough. If no good then make a few enquiries about the nismo plugs and try a copper 7.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2522889
Share on other sites

cheers fellas..

Yeh ill try the bcpr6es hopefully the 6 heat range is better. didnt realise a 5 heat range would be so S!@T

I might even keep the old nismo 8 iridiums in there and just clean them gently..

Ive got the old typical coilpack hairline cracks too, might fix them up as ill probably need too one day anyway..

thanks for the confirmation about the plugs.

Lata.

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2539658
Share on other sites

hey i am more or less going through the same thing i have been using 7es in my 33 and have had no real problems went to enquire about iridiums and could get them for about $18.oo each and the same for platiniums but could not get them in 7,s ended back with old faithful bcp7es for grand total of $21.00 ,cheers

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2540931
Share on other sites

  • 2 weeks later...
Don't know if this has been said but you can't compare all plugs by their number e.g. 5 or 6 as some plug manufacturers hotter and colder plugs ranges move in opposite directions.

yeh cheers, i know, i was just talking about ngk's.

ill be going the $21 option too.. ;)

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2570605
Share on other sites

mine was missing on boost...heat shrinked my coils and gapped my plugs at 0.8 that fixed it...then turned the boost up to around 12psi and it started missing again so i went for the bcpr7es gapped at 0.8 and everytihing is now sweet! id definatly recomend going for the 7...+ it costs like 24 bux!

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2570952
Share on other sites

i'm using the bcpr6es and i'm running 14psi with stock coils. they pop and fart on the very odd occasion, but they are about 7000km old. i'm going to go to the 7 heat range on the new plugs, just to get the heat down.

Remember to check your colder plug for fouling...

NGK FAQ

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2571819
Share on other sites

You can't go wrong with the BCPR6ES plugs. I had a set of splitfire plugs in mine which cost around the $20 a plug mark. They lasted all of 3 weeks before they started missing. Then the car sat for 2 weeks in the spray shop and i went to pick it up and it wouldn't start!

A trip down to Autobarn and 6 x BCPR6ES later and they haven't missed a beat. This was in October last year as well so they're probably due for a change! :P

Link to comment
https://www.sau.com.au/forums/topic/135310-hot-spark-plugs/#findComment-2574762
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Very nice - I also have a 92 GTST and hardly see any others around these days
    • When I need something else to edit, I use Movavi. A friend who does video editing on a daily basis recommended me) it's an easy video cutter to use for beginners
    • I need to edit some videos for work but I'm not good at all this. Which video editor can you recommend?
    • I think you're really missing the point. The spec is just the minimum spec that the fuel has to meet. The additive packages can, and do, go above that minimum if the fuel brand feels they need/want to. And so you get BP Ultimate or Shell Ultra (or whatever they call it) making promises to clean your engine better than the standard stuff....simply because they do actually put better additive packages in there. They do not waste special sauce on the plebian fuel if they can avoid it. I didn't say "energy density". I just said "density". That's right, the specific gravity (if you want to use a really shit old imperial description for mass per unit volume). The density being higher indicates a number of things, from reduces oxygen content, to increased numbers of double bonds or cyclic components. That then just happens to flow on to the calorific value on a volume basis being correspondingly higher. The calorific value on a mass basis barely changes, because almost all hydrocarbon materials have a very similar CV per kg. But whatever - the end result is that you do get a bit more energy per litre, which helps to offset some of the sting of the massive price bump over 91. I can go you one better than "I used to work at a fuel station". I had uni lecturers who worked at the Pt Stanvac refinery (at the time they were lecturing, as industry specialist lecturers) who were quite candid about the business. And granted, that was 30+ years ago, and you might note that I have stated above that I think the industry has since collected together near the bottom (quite like ISPs, when you think about it). Oh, did I mention that I am quite literally a combustion engineer? I'm designing (well, actually, trying to avoid designing and trying to make the junior engineer do it) a heavy fuel oil firing system for a cement plant in fricking Iraq, this week. Last week it was natural gas fired this-that. The week before it was LPG fired anode furnaces for a copper smelter (well, the burners for them, not the actual furnaces, which are just big dumb steel). I'm kinda all over fuels.
    • Well my freshly rebuilt RB25DET Neo went bang 1000kms in, completely fried big end bearing in cylinder 1 so bad my engine seized. No knocking or oil pressure issue prior to this happening, all happened within less than a second. Had Nitto oil pump, 8L baffled sump, head drain, oil restrictors, the lot put in to prevent me spinning a bearing like i did to need the rebuild. Mechanic that looked after the works has no idea what caused it. Reckoned it may have been bearing clearance wrong in cylinder 1 we have no idea. Machinist who did the work reckoned it was something on the mechanic. Anyway thats between them, i had no part in it, just paid the money Curiosity question, does the oil system on RB’s go sump > oil pump > filter > around engine? If so, if you had a leak on an oil filter relocation plate, say sump > oil pump > filter > LEAK > around engine would this cause a low oil pressure reading if the sensors was before the filter?   TIA
×
×
  • Create New...