Jump to content
SAU Community

Recommended Posts

After some thoughts on what could be causing a sudden power cut.

The problem occurs when (for example) I put it into second at say 20kph and fully engage the clutch, then apply full throttle smoothly. The power picks up boost starts to kick in etc, all is fine to this point. Then somwhere around 4.5-5000 rpm the power just dissappears and I get some serious engine braking, if I keep the hammer down the power/boost comes back on again but will eventually cut again.

If I only goto say 75% throttle instead then its fine, smooth power all the way to redline.

So I do some reading around here and I concluded that the aftermarket boost controller was to blame. ECU picks up too much boost and kills the power so as not to blow the engine. Turned it down incrementally a couple of clicks, seemed to raise the rpm of the power cut(not extensively tested). Took that off (now 100% stock under the hood) and the problem persists, if anything its happens at lower rpm.

My housemate suspects that the wastegate is staying open, thus too much boost, running lean ECU does as its job and cuts the power.

Under that theory I found a quiet stretch of straight road and kept a close eye on the (stock) boost gauge. Which went over 7... Housemate reckons it should never go over about 4ish.

Cant really fault my housemates logic at this point, either way Ill probably get it to a mechanic during the week, just after any thoughts/suggestions on what might be going on here.

Thanks guys

Edited by LRP
Link to comment
https://www.sau.com.au/forums/topic/136743-power-cut-on-r33-gtst/
Share on other sites

If the boost gauge reads over 7 that corresponds to more than 14psi, which is bad if you're on the stock turbo, and also explains your power loss (ECU cutting power). 75% throttle = not as much air flow (as WOT) and no timing retard from the computer.

Put it on a dyno to see exactly what's wrong.

Its definately overboosting, does it have a boost controller or anything?

If not check the vacuum hoses going to the wastegate and make sure they are perished or cracked. 14psi on the stock turbo untuned is asking for trouble.

A proper boost gauge would be a good investment.

suspects that the wastegate is staying open

You mean it's staying closed and not venting excess boost, it is closed untill the set boost level is reached then vents the excess, check your vacuum lines to boost controller and on to wategate actuator. Blow hard into the line with it connected to the actuator and see if it moves.

Thanks for the tips guys,

after some head scratching and comparison with my housemates car we determined that some clueless noob put the vaccum hoses on wrong

after about $5 in parts from supercheap and 10 minutes work all is well

thanks again

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oh yeah forgot to also mention need to also unplug the IACV as well. Thanks for the reminder @MBS206 Unplugging the TPS takes it out of closed loop so you're able to screw down the IACV without the ECU trying to add/subtract timing to maintain the idle (not sure PowerFC can even do this, but Nistune and the OEM definitely does)
    • For sale is my 1999 Nissan Skyline R34 GT-T, tuned to 234 kW / 313 hp. I've had the car for a few years as my daily driver. The car is original (as far as Skylines go), with only a few minor upgrades to enhance performance and driving experience, as typical for such a car of its age. Overall, it is in great condition with no body rust, thanks to its earlier import date. It features a top-notch security system (not literally, but it's great!) with remote start and still functional 4-wheel steering via HICAS. It comes with several performance and handling upgrades, including:     Hypergear 450HP Turbocharger running 17 PSI boost, installed mid-2021 by Jaustech     550cc injectors     Nistune ECU     Front-Mount Return-Flow Intercooler     X-Force Stainless Steel Exhaust     Upgraded engine mounts     Bottom end bearings replaced     BC Coilovers     Lenso DR1 rims     Bridgestone Potenza Adrenalin RE003 TL 245/40R18 97W tires, fitted early 2023 The interior is mostly stock, with a few additions:     Viper Satellite Tracking System with remote start     Bluetooth Double-Din Touchscreen Head Unit     Steering wheel cover Cons:     A few paint imperfections here and there     Driver’s seat shows more wear than the others. It's not torn at all, but I've added a seat cover to protect its condition. I also have a CarVX Vehicle History report available for serious buyers, so you don’t need to purchase it yourself. Price: $26,000 ONO.
    • I've had two suzukis in the past have an extremely hard time turning over and not starting after sitting for a few weeks. Ended up the alternator would seize up causing the starter to force. Same issue both times.  Maybe they're sourcing their alternators from the same place...
    • Ah right. Maybe my rb just loves chewing through batteries lol.
    • On the R34 can't you just unplug the IACV? This is the way I've always done it on the R33. Disconnect IACV, get it idling around 650rpm, and then do a power reset on the ECU to get it to relearn idle (factory ECU).   The big reason no one has touched on as to why you'd want to get the base idle right, is that it means the computer needs to make smaller adjustments to get a good idle at 700-750rpm.   Also, cleaning the IACV won't normally make the car suddenly idle lower or higher. The main issue with the IACV gumming up is that the valve sticks. This means the inputs the ECU gives, aren't translating to changes in air flow. This can cause idle choppy ness as the ECU is now needing to give a lot of input to get movement, but then it moves too far, and then has to do the same in reverse, and it can mean the ECU can't catch stalls quickly either.
×
×
  • Create New...