Jump to content
SAU Community

Recommended Posts

Ok - I have a brake issue I'm not 100% sure how to fix or what's causing it.

Basically I'm not holding brake pressure - aka the pedal is going to the floor.

If you "pump" the pedal and hold it - it will hold pressure fine however. But if you release the pedal about and wait 15s or so the pedal will go straight back down to the floor again. I've bled through about 2L of brake fluid through and the problem is still there. And no stage have we seen any signs of bubbles when bleeding either.

The problem has been there ever since I experimented with a hydraulic handbrake system. When you applied the hydraulic handbrake you could feel the pressure come back through the foot brake pedal however. The hydraulic handbrake has since been removed as it was usless for my wanted applications.

Is it possible that the hydraulic system has wrecked my master cylinder or is there something else I should be looking at? (When installing the hydralic handbrake we did accidently run the system dry once (no fluid) and apply the foot brake). Or is it possible the problem is somehow related to the ABS unit instead as the ABS and the hydraulic handbrake were not friends?

Any advice is appreciated as I don't want to go pulling things appart unnecesarily.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/136948-brakes-wont-hold-pressure/
Share on other sites

If you push the pedal all the way down while bleeding, you've probably ruined the seals in the master cylinder.

When you are braking in your car, your brake pedal usually only goes about half way down so the piston in the master cylinder only goes part way of its full travel. If the master cyliner is old or the fluid has not been flushed regularly, the far end of the master cylinder can get pitted from rust or have grit in the fluid down the far end. If when bleeding, you push the pedal all the way down, you can cause damage to the cup seal in the master by running it over the rough surface down that end.

If the master has been freshly rebuilt and the bore given a light hone, then it shouldn't be a problem.

Snowy, sounds like the master cylinder needs a freshen up mate.

Just in case it isn't, is it losing any fluid? Any leaking inside the footwell? Around the ABS unit? Does it do it with the ignition on and off?

R32's have a real problem with leaking ABS units so not unheard of.

Anyway sounds like the classic master cylinder seal failure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know mentally you're set on the ATS clutch but honestly I'm a big fan of the Nismo Super Coppermix Twin. It's much cheaper and in some ways I think it's a better design for a street/circuit car.
    • Just checked in first post and you should be able to bring it home November this year, right? I'm amazed you made it through four years of this. As hard as it feels now the rest will go by in a breeze in hindsight, I'm sure.
    • Realized I haven't been back here in a while. Still here, still alive, still waiting for the car.  I went back again the only time last year from Oct-Nov for R's Meeting and drove it around some more, including a few laps on Fuji Speedway(in the wet, sadly). The car still feels good, but have a couple small things to address. I've been getting more parts but have slowed down still, and most of the bigger purchases are now out of the way. I find myself getting impatient more and more when it comes to getting started on this project; it's quite hard for me not being able to really dive in and start making this car my own because it's halfway across the world. At times it doesn't even really feel like I own one of these. Haven't really been motivated or had the desire to document the last trip on here or social media for, well, reasons... but here's some pics...it's also still alive and well as you can see: I've narrowed down to the last large part purchases(anything over $2k) before the engine build to be: 1) Ohlins Road & Tracks 2) ATS Twin Carbon clutch 3) Endless BBK with some custom options and 4) Kansai Service carbon driveshaft I don't think the budget exists for all of these this year, but I'll try for one or two items I think. Though, every time I look at my spreadsheet I sigh, shake my head, and get depressed just that little bit more.  'til later.
    • It's a stunning location!  I've been to NZ twice but haven't made it to the North Island yet.  Definitely on the cards but the South Island is hard to tear yourself away from too... Looking forward to see what you can wring out of it once you can get it to hold together!  Be awesome to get a low 11 or even sneaking into the high 10's pass out of it.  That's a bloody quick car that most people will never experience in their life.  Enjoy!
    • Nominally yes but I’m not really at that stage yet. Outsourcing to Japan is also a relatively good deal at the moment because their currency has devalued much more against the USD.  You would assume this but a lot has changed from the pandemic. Mechanics are in short supply and demand for fixing old cars has gone up from the cost of new cars. 250-300 USD/hr is not an unusual shop labor rate in California and you’re paying that regardless of whether the guy is competent or not. Coworkers have been quoted 3000 USD for a water pump and thermostat at a dealer on an N54. Oil changes went from ~75 USD to 150 on fairly normal cars like Civics. The cost of the oil and filter hasn’t even kept up with inflation.
×
×
  • Create New...