Jump to content
SAU Community

Recommended Posts

  • 2 months later...
  • Replies 108
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 5 months later...

Too right mate! .

Ok it's been a little while since ive updated this thread , i figure it's about time to ... I've spent the last coupleweeks on holidays , so after quick tidy up of my block (house) , i've been into this thing and my track hack since , both are pretty close to rego , i just need some stock front struts for this one :) . pics

post-20231-0-43819700-1358433794_thumb.jpg

post-20231-0-10111400-1358433803_thumb.jpg

post-20231-0-07643500-1358433810_thumb.jpg

post-20231-0-65951700-1358433814_thumb.jpg

post-20231-0-46866100-1358433818_thumb.jpg

  • 3 months later...

after this weekend , i have a month to get this thing complied pretty much , so it will be full steam ahead! actual things to do are:

speedo sender needs fitting (i have a 32 gtr one but apparently they need the cog to be changed also)

fit front struts

bleed clutch that now lives on the carpet

fit spare tail lights

fit 33 gtr rims

find my ecu (currently has power fc running it)

fit r33 standard exhaust and cat (minor modification may be required)

fit standard castor rods , rear arms and hicas lock (or fit the non hicas cradle i have laying about)

remove 2 way diff

wash/buff maybe polish and i think that will about make it ready! (hopefully i get away with the gtr injectors and z32 afm)

after all of that is done , it will have every bolt on bit i have bought over the years bolted and tuned within a week of it being rego lol . I figure this car has been pushed to the side for so many other cars i've promised myself not to touch another until it is up and registered!!!

Edited by toffy

street rego'd ceffy's are getting harder to get hence why im getting mine complied now!

by the way Toffy, what ever happended to that street dancer Cefiro? Did you part it out or keep it?

I want some parts from that car!!!

  • 2 weeks later...

Yeah I've wanted this car Regd for years , I actually have a complied shell laying about I'm half tempted to swap everything into , the purple one is rougher than I like , especially after that rear hit . Yeah I still have the complete car , minus the front bar which is promised to Dan :) , and all the trim is in purple now

Edited by toffy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • To be determined, Luke, to be determined. 馃榿 Definitely the car
    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It鈥檒l be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
  • Create New...