Jump to content
SAU Community

Recommended Posts

you know the mods

Nerve essential ECU (remap in Japan)

4" cat

3.5 apexi exhaust

stock injectors

stock pump

stock reg

Trust FMIC with custom core

pump and reg i am changing very very soon.

HKS pod.

Yes i know the A/F is border line ATM

but good result from a HKS 25/30

18 psi (and yes i need a new boost controler)

but ECU mapping is perfect

post-14621-1159874770.jpg

Link to comment
https://www.sau.com.au/forums/topic/137184-new-dyno-reading/
Share on other sites

you know the mods

Nerve essential ECU (remap in Japan)

4" cat

3.5 apexi exhaust

stock injectors

stock pump

stock reg

Trust FMIC with custom core

pump and reg i am changing very very soon.

HKS pod.

Yes i know the A/F is border line ATM

but good result from a HKS 25/30

18 psi (and yes i need a new boost controler)

but ECU mapping is perfect

ive got pretty much the same mods as u do including the HKS 2530, except my ecu is stock and i got SAFC II and a hybrid FMIC, n im getting 232rwkw @ 1bar..

next mods will be PFC, fuel pump, n injectors hoping to max the turbo out at around 260rwkw..

nice results btw..

I would imagine that power reading would have been that high because it was leaning out ??? as at 9psi that power should not be possible. Then again all dyno's read differently. What were your afr's on the day ???

with standard turbo, standard pump and standard injectors (later turned out rotted), fmic, exhaust, splitfires, link ecu and 9psi pulled 211kw at autotech

motor blew up two days later :laugh:

Good figure, i made 242 on autotech at fyshwick with my hiflow garrett ??something?? turbo. So I know what sort of fun you are having at the moment. And yes your mix is lean, i think the worrying thing about that is its lean from the get go. Generally they start out OK and then lean off as revs/power increases near the top. Do the changes you intend, I'd also think about injectors.

What was the duty cycle like? Std ones would be close to maxed out wouldn't they.

here is the full one, the quality is not so good, using my phone to get it on to the computer.

tridentt not sure what the duty cycle is at, see how things go after i get more fuel through the reg and pump.

post-14621-1159930333.jpg

Edited by race_snooze

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 馃挭馃徏 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 馃ゲ But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
  • Create New...