Jump to content
SAU Community

Whats Soooo Special About Nur

Kushil Abeysinghe
 Share

Recommended Posts

R34GT-t_07 Enthusiast

R34GT-t_07

Posted
Posted (edited)

For one thing its a lot more powerfull it has around 260-300kw it has compleatly diff internals then other 34. It also uses diff turbos also the suspension is diff too that is why there is a masive price tag on it comparing to a ordinary $60000 GTR as its more faster and a looooooooootttt more better. i hope that answers ur question.

Edited by R34GT-t_07
funkymonkey Grand Master

funkymonkey

Posted
Posted

factory leather interior? hehe

its a limited production run, basically with all the best options available to the R34 GTR put into it. Its like owning an R32 V Spec II, or a genuine R33 400R etc.

thrtytwo Veteran

thrtytwo

Posted
Posted
it has a 5 start rating wich is pretty rare from what ive been told. Not to mention the mods.

On the latest Hot4's DVD they say for a good condition GTR your looking at around $90k, so i guess its not that over priced.

'good' or the best lol ?

i know that paying 50k wont get you a nice car at all but i think 90 is at the extreme end. (not that you couldnt pay more)

Beer Baron Grand Master

Beer Baron

Posted
Posted

you are kidding right? it has 20,000kms. it's a NUR spec, limited edition V Spec II. it's a 2002 model. it has some nice choice gear on it, but not too modified so it doesn't lose any of the original NUR attractions. all those things rate a price difference between it and a cheapo 1999 grade 3.5 with 80,000kms, non-vspec, no mods etc.

  • 3 weeks later...
Kushil Abeysinghe Enthusiast

Kushil Abeysinghe

Posted
  • Author
Posted

ya, i guess its a very special thing to have if your a GTR addict....Un-presidented bragging rights --- need to have pocket map of Nurburing track of cause........... :devil: , just in case people ask what NUR stand for.......

Its like a Rex 22B of Nissan GTR's......or will that tag go to the Nismo Z tune

wrxhoon Grand Master

wrxhoon

Posted
Posted

Good used NUR v-specII or NUR M-spec examples bring as much or more money that when they were sold new in Japan.

You can't compare this car to a 99 model GTR ( non V-spec) with 100k k's and more than likely full of rust that sells for 3 mil JPY ..

For the record only M-specs and NUR M-specs have the factory leather trim, NUR V-spec II's have the normal GTR seats that any V-spec II has ( darker than series I). They do have steel wheeled turbos with ajustable actuators and 300kmh speedo.

Suspension is the same as normal V-spec II ( if its a V-specII ) and same as an M-spec if its an M-spec.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      Thanks Santa (the neverending trials of the 400,000klm, 400kw, RB30, manual swapped Stagea)

      By soviet_merlin · Posted

      Thanks Duncan! Yeah it's street use for me only. Maybe occasional track day. Any difference in noise when running with the two pumps? I would expect the lift pump to be more quiet than the main pump so hopefully not? And yes, unfortunately quite a big price difference to the simple hanger setup. Though I'm usually willing to trade money for better reliability and future-proofing. Buy once, cry once and all that. I'd be very happy to never have to deal with fuel pump / wiring issues again  
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      The old manifold was quite under the GTR strut brace.  The new manifold is quite [unknown] the GTR strut brace. The GTR strut brace was needed to clear the bonnet vents. The Old strut brace will almost certainly clear the new manifold, but not the bonnet vents. The old strut brace will almost certainly clear the new manifold, and the new bonnet without vents. But I am hoping the GTR strut brace clears the new manifold :p
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Bonnet clearance?
    • joshuaho96
      Magnetic Drain Plug Snapped in Half

      By joshuaho96 · Posted

      On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, more pain. The FAST manifold is a little larger than the stocker. This is problematic because there really wasn't much clearance to begin with, so going from 'barely enough' well into 'no' is sad based on the external dimensions of the thing, even though where it bolts to the head is the same. Result is the fuel rails sit a good 25mm higher, and this is a bit of an issue with the wiring that runs behind the motor, and the fuel lines, and everything else. When pushing the manifold on, it required a huge amount of force to crush wiring looms to fit it, sensors like the MAP sensor are about 1mm from the firewall, and the FPR just has to bend ABS lines to be forced into place. After some brainstorming and some sad drinking, the loom for some reason ran from the grommet behind the ABS sensor, then to the driver side head, then back to the passenger side head. So all of this was pulled back and stripped, a few wires cut and rejoined, so that the 'branch' was now on the passenger side's head as below: Before you basically couldn't see anything behind the driver head. This is much improved! The MAP sensor is now pointing up (instead of at the firewall) Brackets have been made up for the rail. The rails are for a LS1, the manifold is designed around a LS2 as it's base. Which of course has slightly different bracketry and water pump clearance, hence the mods people need to do. Should be hopefully mounted tonight. I spent money on a new FPR that is slightly more compact than my Turbosmart FPR1200. The gauge has also been moved to the rail. There's also apparently an ORB to AN Union instead of the adapter, because the ~25mm of the current adapter is going to make the difference. Provided this all goes together and arrives today, it'll be the totally not stressful attempt to start it.
×
×
  • Create New...