Jump to content
SAU Community

Recommended Posts

240Z pilot October 9th, 2006 10:05 PM Link

I guarantee this car will be significantly HEAVIER than the “7 litre us tank” referred to! Z06 Corvette weighs in at 3150 lb., this will be at least 3400. I’d bet money it will also be SLOWER around any race track.

To tell the truth, I’d rather see a new Silvia (which we haven’t had in the U.S. since ‘98)!

This thing is a bit “much of muchness” imho.

Less is more!

;)

idiots...

Theres another thread posted recently with pics of the car without the car bra and hiding stuff but I think it is still labeled as the prototype.

http://www.skylinesaustralia.com/forums/in...007+skyline+gtr

Drew.

:P idiots...

Its not that much of a stretch of the imagination.

The current Z06 runs a 7:43 around the Nurburgring Nordschleife. That's significantly faster than a 996 Turbo, a 415hp / 3800lb AWD car with a purpose-built chassis and a lot of money thrown into performance R&D.

That said, I don't think Nissan will be happy with the GT-R until it holds the lap record for a "reasonable" production car (I don't count the Radical SR8 as "reasonable", even though technically it is a production car). And the 996 is a generation old, now, but I don't have the times for the 997 Turbo. It should have cracked the 40's by now, since the old 996 Turbo / light tune R34 ran a 7:51 or so.

I think the next GT-R will be quicker than the Z06 on the track, but given the sheer pace of the Z06 its not going to be your typical "AWD turbo terror vs Yank Tank" battle, especially in the hands of drivers who know how to make a car go around a track fast.

The real thing looks the goods thats for sure.

The one problem I can see with this is, nissan isnt seen as a premium brand, therefore the people with the money are going to be hard pressed to justify spending the dollars to buy it, as it doesnt have the 'badge'. Because really a clubman will go around a track as quick as a porka at a fraction of the cost, and a VK with a worked V8 in it will go in a straight line faster at a fraction of the cost. But the people with the money wouldnt do that as they dont have the badge. Ones a mechano set the other is well a commodoore.

But yeah, good luck to it. Its definately got all the good gear.

people still thinking it's a Skyline after it's been explained it's NOT a million times, others thinking there is going to be a V8 for the US market only? no... they're idiots :)

Other sites are linking to 2005-dated information saying it'll be badged Infiniti over there as well.

Its almost the end of 2006, for Christ's sake.

I love it how people are still quoting the info I posted from back in 2004:

http://www.leftlanenews.com/2006/10/09/spi...08-nissan-gt-r/

Rumours have indicated the car will feature a 3.2 liter twin turbo V6 engine with 480hp.
I think the next GT-R will be quicker than the Z06 on the track, but given the sheer pace of the Z06 its not going to be your typical "AWD turbo terror vs Yank Tank" battle, especially in the hands of drivers who know how to make a car go around a track fast.

Which lets face it, isnt most americans who think in 1/4mile and not much else, guess theres the handful of people outside of NASCAR that actually know how too turn right as well as left.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...