Jump to content
SAU Community

Recommended Posts

Just for a laugh.

1985 honda civic

890kg

1.6l DOHC ZC (not vtech yo) jap spec engine implant. 130HP at the crank from factory.

Mods: Extractors

rev cut 7500

15.5 down at WSID

100HP atw (75kw) lol at R31 club dyno day

Don't have it anymore.

i got a chrysler gallant

its got a custom exhaust (i cut it myself)

single down drought carbie(vacuum secondaries dont work)

and blown piston ring

"power" my guess bout 30kw at the rears lol

  • 1 month later...

Model - Swift

Engine - G13B

Modifications - Extractors, exhaust, cold air intake, BD14 cams, cam gears, Enlarged throttle body, group A chip, remapped ecu, dog box, msd coil set,

Dyno tune results 54kilowats before, 88 kilowats after

there was man other mods i just forget,

high 14 pass.

  • 3 weeks later...

put the pulsar on my mates dyno last night. made about 82kw, about 2kw down on what it made on a different dyno about 6 years ago. plenty of power left in it though. AFR's are mid 11's. now to convince the missus to let me put a nistune on it.....

  • 4 weeks later...
Engine:VQ35DE

Car: V35 Skyline Coupe

Mods: Z-tube and pop charger, Plenum spacer.

Power: 177rwkw.

Putting the Exhaust Headers on monday and a grounding kit. Will do a new Dyno run sometime next week. :P Hopping for 185rwkw

Finaly got the car on the dyno after getting the extractors and light wieght pulleys.

191rwkw now. Pushing for 200 :rofl2:

  • 3 weeks later...
  • 1 month later...

Some history on the RB20DE in the rally car:

2082010122631pm.jpg

Come a long way from it's first run of 97.5kw!

Spec's are:

RB20DE (235,000km)

Independent throttles (4AGE)

Ported head

Cams (270 or 280° can't remember)

Link G4

8,400rpm Rev limiter inguaged 4176 times in 2 years. That's not counting bouncing off the limit either. Rev it much?! :)

Z32 NA with exhaust/extractors/pod/chip yielded 240kw

My R32 with similar mods dynoed 222kw.

Battling to extract more though.

Errrrm...i think you were meant to say horsepower...240rwkws is somthing like 320-330kws at the flywheel.

Errrrm...i think you were meant to say horsepower...240rwkws is somthing like 320-330kws at the flywheel.

I think he's just talking crap as a Z32 NA will all that wont make 240rwhp/rwkw in any case.

  • 2 weeks later...

Rb30e

Today I made:

97.5rwkw @ 120kph

321nm @ 88kph

Rev Limiter @ 6500rpm

Specs:

Stock RB30E

Stock Timing (+15)

91 Fuel

Extractors & 2.5" Exhaust, Stock Cat & 1 Muffler Before Diff

3" Intake Pipe, Cheap Pod, Custom Airbox & CAI.

Going to run it on 98 Fuel Next time & +20 Timing, aiming for 100rwkw, also need to sort out the issue with it running rich.

  • 4 weeks later...
94 r33

rb25de

stainless steel extractors, cat back, apexi pod.

95.7rwkw...

update today i got 101.7rwkw with new catbak and timing advance in 4th gear run

what size exhaust do you have from the headers? and what size from the cat back?

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...