Jump to content
SAU Community

Recommended Posts

Green over light green Toyota Celsior.

4.0l 1UZFE V8 Engine

181xxx k's, engine is running perfect.

No mods, apart from 20" CHrome XHP Shorelines.

Everything works, car runs like a dream!

Few scratches here and there, but the car is in awesome nick.

Cream leather interior, woodgrain dash, no rear massaging seats.

Rego till 12th month, can prodive a rwc ...

Have an aftermarket height controller on the way, which can be included.

Im interested in swapping for an r32/33 or a nice s13 (basic mods, or something turbo). no CELICA's or fwd rubbish. Must be rwd and manual turbo.

Am negotiable with and without the 20's. Will be getting a service done before handover.

0422312860, Give me a call, take it for a spin, and we can sort out something ....

Located brisbane northside. The name is Lee, dont be shy :P

car1ua4.th.jpg

car2vz0.th.jpg

car3an7.th.jpg

car4ya8.th.jpg

Edited by Burgz
Link to comment
https://www.sau.com.au/forums/topic/138234-toyota-celsior/
Share on other sites

1989 3L Turbo Supra.

HKS 3 inch Super Dragger exhaust and muffler.

HKS Blow off valve

Aftermarket side skirts

APEXi SAFC

Air con,

Cruise control,

Power mirrors,

Power windows,

Power Steering

Auto.

Near new tyres.

Excellent condition.

http://www.skylinesaustralia.com/forums/in...st&id=54777

Link to comment
https://www.sau.com.au/forums/topic/138234-toyota-celsior/#findComment-2601092
Share on other sites

1989 3L Turbo Supra.

HKS 3 inch Super Dragger exhaust and muffler.

HKS Blow off valve

Aftermarket side skirts

APEXi SAFC

Air con,

Cruise control,

Power mirrors,

Power windows,

Power Steering

Auto.

Near new tyres.

Excellent condition.

http://www.skylinesaustralia.com/forums/in...st&id=54777

Thank-you for the offer mate, however im looking towards something that is manual. Good luck with your sale :P

Link to comment
https://www.sau.com.au/forums/topic/138234-toyota-celsior/#findComment-2602010
Share on other sites

say your not interested in the for a swap cause its fwd.

but check out the lancer in the for sale section or here

http://www.boostcruising.com/forums/index....howtopic=160562

thanks for the offer mate, but i would prefer a rwd! Very nice car none the less

Link to comment
https://www.sau.com.au/forums/topic/138234-toyota-celsior/#findComment-2602928
Share on other sites

Is this car from Morayfield, mate? or do you go through there from time to time? think ive seen it, hey. If so, nice ride. A month ago i wouldve swapped, but oh well. GL with the sale.

Link to comment
https://www.sau.com.au/forums/topic/138234-toyota-celsior/#findComment-2602949
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I vote go red. Only because I hate keeping gloss black clean. Was no worries helping out either! Glad you've survived the rain outs of QLD
    • I would again like too thank Matt for his help in me sourcing the detachable hard top for the little red car, without Matt's assistance in inspecting it and locking it down, I can guarantee it would have sold before I could get up to see it,  and as that was the only available NC hardtop in Australia, I consider myself extremely lucky on multiple levels To say I'm more that happy would be an understatement And, it is 100% water tight, I drove through torrential rain coming back south, and by torrential, they type of rain that doing 40kph in a 110kph zone was a real thing, and even then, the standing water on the Hwy was deep enough to throw waves I'm also more than happy that the huge "BEASTS" that Matt calls dogs didn't eat me for lunch, I'm sure the sniffs and licks were more to "taste test" me, over being to friendly Now to work out what colour to get it painted, panel match, or gloss black........first world problems are real
    • Actually I might have figured out. Looks like there is a tab according to google images but it's hidden. Silly me.
    • No clips on this one like the other connector. Only that red tab that I can push slightly up.
    • For any loom connector that has an obvious release that resists pushing far enough to unclip, just spray some silicone lube into it. You might also benefit from using a bent screwdriver or small pick to push in the right place at the right angle.
×
×
  • Create New...