Jump to content
SAU Community

Recommended Posts

where would i take this to get it fixed, is it expensive.

is it steering bushes ? ive seen that term thrown around

only starts wobbling at 100kmph + but i still dont like it >.<

i tried searching but couldnt find anything :)

help would be appreciated :D

Link to comment
https://www.sau.com.au/forums/topic/138476-steering-wobbles/
Share on other sites

what type of tyres have you got?

sometimes its the tyres. weak sidewall tyres like nankangs can give you the shakes at high speeds.

a guy i know put these on the rear of his xr6 ute and it was wobbling all over the fwy. he took them off the next day, problem solved. and that was on the rear.

You need new uni joints in your tail shaft. Trust me, my old car did it. BADLY (Uni was shot to pieces) replaced, shake gone.

Skyline does it too, and I know the uni joint in tail shaft needs replacing.

Do you get a "clunk" at all when you go from 1st, to reverse (When on the spot with engine running) and then go to reverse?

If you get on the gas once the vibration is up, it all goes away doesn't it?

You need new uni joints in your tail shaft. Trust me, my old car did it. BADLY (Uni was shot to pieces) replaced, shake gone.

Skyline does it too, and I know the uni joint in tail shaft needs replacing.

Do you get a "clunk" at all when you go from 1st, to reverse (When on the spot with engine running) and then go to reverse?

If you get on the gas once the vibration is up, it all goes away doesn't it?

only problem with this is that he said he feels it through the steering wheel but the car isn't shaking. if the uni is gone you should feel the car shake. if it is shaking the steering wheel then it is either suspension or wheel balance.

i will be getting it balanced during the week, didnt have time today. will see how that go's. but i also need some stiffer suspension :S my rear tyres rub the guards quite a bit even under soft turning, they dont slice the tyre, just rub, but it still sounds shit !

p.s. when i bought the car i was told it had aftermarket suspension but i had a look and unless its well ran in i highly doubt it. its dirty as heck and really soft.

Edited by thrtytwo

Hmm. I had this on my '33 GTST..... it turned out that one of my front bushes had been broken (read smashed) by a pothole that had seriously damaged both front rims...

I ended up having to get a WhiteLine poly brush set.. I'm not sure of the right name for it, but they were <> 100 from Just Jap...

They were nice yellow plastic bushings, cylindrical, with a hole through the middle, and a lip on the outside.

If you need to, i'll have a look through my receipts....

The Symptoms I was having :

Shaking on the steering wheel, but not always. When shaking it felt rhythmic, similar to having an out of balance wheel, or *BENT* wheel.

(Yes, I know what that feels like, thanks to NSW rural roads... go the RTA! )

Sometimes, it would go away for a day, then a small bump in the road might set off the shaking again.

No other shaking etc for any other part of the car, that I could tell.

If this has happened to you, check *VERY* carefully for serious excess wear on the inside edge of both front tires.

(When we worked out what it was, the inside edge of one of my tires was down to the canvas, while the outside was <>60% )

Sorry for the rambiling post... hope it helps.

i knew the rest just not the 94 bit :)

thanks though !

and to the post before you, i only bought the car last thursday, so it has brand new tyres on it, which means if there was a wear pattern to see, i wont see it. Ill see what happens during the week, if it still wobbles after wheel alignment i will get new bushings ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
×
×
  • Create New...