Jump to content
SAU Community

Recommended Posts

I have been under the impression that to run full slicks at a track day you need to have a cage.

I cant find information on this anywhere in the cams book or website.

If this is the case, can anyone tell me the details and where they found this info..

Cheers

Link to comment
https://www.sau.com.au/forums/topic/138534-slicks-whats-the-requirements/
Share on other sites

not true. even in super sprints you dont need anything other than a track worthy car that meets the sup regs of the event you are entering. if you want to run slicks then you just have to run in the class that they meet (i think SVD or 4D).

check the supp regs because the ones I have in front of me say

ELIGIBLE VEHICLES:

Cars participating in the event are required to comply with the relevant

NCR’s as defined in Section 6, Schedules A and B, including the following

requirements:

Roll-over protection which complies with Schedule J of the 2006 CAMS

Manual if race tyres (eg slicks or grooved slicks) are fitted.

yep, i guess it pays (which I did say) to check the regs. but for track days ie days not run under cams approval you dont need squat, just whatever the organiser deems appropriate.

Its a supp regs thing cheater. Also be warned, running slicks will probably make you slower. Requires different suspension geometry to what you are probably already running and have to consider carefully the tyre you want to run.

A slick doesnt mean soft and sticky, you may find that even after 4 laps they are not up to temp and you are still sliding around. By that time you have cooked your water and oil temps and your brakes are shagged

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From the pictures I have when doing the job the flywheel is the same diameter, I don't think they're playing weird tricks like putting weights at the outer diameter to increase flywheel inertia or anything like that. The OEM flywheel is definitely heavier, but it's not a huge difference. Quoted weight savings of the clutch is 2 kg so I can't imagine the flywheel being lighter than ~7 kg. Kind of regret not weighing it before the clutch went into the car but as far as driveability goes I have no complaints.
    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
    • Hello friends, i have a good friend in Canada that looking for a good condition 1993 GTR around him please if one or know someone around you that is willing to let it go please let me know so that i can inform him.....Thanks
×
×
  • Create New...