Jump to content
SAU Community

Recommended Posts

Hey guys,

Love the car, absolute blast to drive, however now that i've been driving it for a bit, i'm starting to look into its hopefully minor issues.

Issue 1) After full wheel alignment and balance, car still has slight vibration at high speeds - i'm calling shit tyres since the guy at the workshop said the rear's where out of whack and slightly egged just want confirmation.

Issue 2) Car pulls to the left if I let the steering wheel go - car has coilovers but are old and way to hard and i think oversprung, possibilites? castor rods? control arm or something i can adjust?

issue 3) how to tell if car is over sprung - i think it is, had 2 people get in on the passenger side, was sagged and i could 'feel' the damper move and actually work rather than the spring just bounce around like usual - my thinking is with more weight its stopped the spring from moving as much and allowing the damper to do its job. With just me in the car, if i go over a large bump you can hear the springs 'resonate' and clang around.

Issue 1 and 3 i think can be fixed with new tires and a change in suspension, issue 2 i'm not sure about. No obvious viscous fluids so i'm not sure about the castor rods, but my mechanic is away so i can't talk it through with him.

Cheers guys! For once i'm actually looking forward to working on a car!

Link to comment
https://www.sau.com.au/forums/topic/138960-couple-of-handling-questions/
Share on other sites

1. is the vibration through the steering wheel or through the seat?

if its through the seat, more than likely its the rear tyres fault as the guy said

2. cars pull with uneven camber and/or castor. they pull to the side with less camber/castor.

to fix the problem get castor rods/bushes. if the camber is uneven too get camber bushes/arms.

all this information will be on you wheel alignment report. both camber and castor should be very close to even.

if there is castor adjustment, wheel aligners will set the left up with 0.5-1.0deg more castor to accomodate for the natural camber of roads (which allow for water drainage)

Edited by salad

well there's my answer for the pulling to the left, wheel alignment report shows left at +4.41 degrees and right at +5.57 degrees.

Are the castor rods seperate to the bushes or are they together? Just replace both?

Vibration is the last thing ot worry about i guess, it only happs at about 110km/h plus. Before the alignment it was about 80km/h plus

sounds like front tyres still out of balance... alignment wont affect vibration.

rods are seperate to bushes. replace the bushes in the stock rods or replace the whole rod with an aftermarket rosejointed item

bush's are the more street friendly option.

i think you can get enough adjustment out, but im not sure, someone else will have to clarify as i've never had bushes.

rose jointed rods have a lot of adjustment, more than enough, but they're not recommended for street.

rose joints are illegal on the street, because when they wear out they fall apart.. Having your suspension detach in the middle is generally not a good thing :laugh:

You don't need that much adjustment on the street. On the track, sure.. especially with semis :)

If your alignment is fine but the bushes are clapped out just get the bushes replaced. Otherwise get adjustable castor rods and have at it (have seen the noltec ones for a 32 GTR and they make a brick shithouse look like a tent).

Vibration is either caused by out of balance, cheap out-of-round tyres or that your wheels aren't perfectly true on the hubs (you will probably get brake vibration if this is the case because the rotor will be out as well). Edit - if your wheel bearings are on the way out that can cause it too.

If the springs are bouncing around like you say it sounds like the car is oversprung. Personally I think it's foolish to run rock hard suspension on aussie roads, get some nicely matched springs and shocks instead!!

Edited by Kinks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes...but look at the numbers. There is a tiny tiny fraction of the number of Joules available, compared to what is used/needed. Just because things are "possible" doesn't make them meaningful.
    • Thanks for taking the time to post that ! If anything changes or happens please do update us. 
    • Somehow Vertimass/Oak Ridge National Labs has figured out a catalyst that can convert ethanol into C9-C10 hydrocarbons in basically a single step without ending up with a bunch of ethylene or similar waste products: https://patents.google.com/patent/WO2023224867A1/en I still don't think anything like this will keep us from needing to transition to EVs regardless along with all kinds of other electrification, but things like this will go a long way towards alleviating the problem of how to electrify things like planes. Renewable diesel is seemingly an easier problem as well, Chevron is already running refineries for the stuff and the primary feedstock is tallow and other waste fats from agriculture.
    • Ok so I have sorted everything with my uniclutch and  i can offer up a bit of feedback and some things that might help others.    I found problems with factory damper line. Weird shit and had trouble with peddle adjustment    I used this https://au.gktech.com/products/r33-gts-t-skyline-braided-clutch-line?_pos=2&_sid=22b01b9b9&_ss=r Also when adjusting peddle leave a bit of play. You can get into a over stroke condition easy.. Make sure you can push the slave forward after adjusting to confirm fluid can return to master then you will need to pump it up heaps…..not sure why but that’s how it is.    last thing the splined adapter is machined perfectly. If your input shaft is old like mine was I would put a bit of valve grinding paste on it and stroke it like a 15 year old. Just to give it a tad more clearance and to better match it to the spline.    reason is on a near flat shift I have had situation where the peddle returns a millisecond after you lift from the clutch. No slip or anything but I reckon this is due to tolerance on the spline being way tighter than stock clutch and binding for a sec. I think this will go away but also my spline was old. Box is old so I guess I should have checked better. It’s a super neat fit.    it feels light as and holds awesome without any noise    
    • My Fuga Hybrid is JDM, 2014 model but very similar to the V37 from the looks of things..same platform just physically larger and very comfortab;e
×
×
  • Create New...