Jump to content
SAU Community

Recommended Posts

how would the cat affect it?

update: i got home this arvo (been driving with the o2 sensor unplugged) and plugged the o2 sensor back in. seemed to run fine. then the aircon switched off, and it ran slightly crappy. turned aircon back on and ran fine. watching the gauge it runs leaner with the aircon on, and richer with the aircon off. so i'm thinking it may be fouled plugs, or possible the idle control, but i'm open to other suggestions.

Edited by mad082
Did you say you cleaned your Afm's..........did you open them up and re-soldered the joins?

Just curious........what colour is the shirt?

yes.......... yes.

thats ok........ blue

Edited by mad082

i don't think it is the throttle cable. the reason is that i can sit there and it won't do it. then it might do it for a second then it will go away. or it will hunt so bad it stalls the car.

i'm giong to clean the AAc valve again. last time i had this sort of issue it was the cause, but it had slightly different symptoms. it would hunt, but the idle would sometimes sit at 600, other times 1500.

  • 1 month later...

i know it is digging a bit, but this morning my car a had a slight missfire for about 5 secs on really low acceleration. No boost prob still running - pressure in the manifold. The car had warmed up or was close to it, and it is the first time it has done it. It has not done it since, only that short time.

Just wondering MAD082 if you found out your problem? or if anyone knows anything new.

i ended up altering the tps, putting a new fuel filter in, cleaning the afm, changing back to my old o2 sensor, got rid of some vaccum leaks.......

i think that was all, and yes it did go away. i think the vaccum leak was the main cause. it was the breather hose on top of the rocker cover, and also the seal around the pcv valve that i found to be leaking.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...