Jump to content
SAU Community

Recommended Posts

hi guys,

over in campbelltown we have a line in trouble..

car starts and idles, will rev out of gear, but if you drive it the engine will cut out with no stutter or shudder just off. It will turn back on and drive another 50m before shutting off again.. what the heck is wrong with his car?

any ideas appreciated. We have checked most things already but cant find anything wrong

Link to comment
https://www.sau.com.au/forums/topic/139254-rb25det-cutting-out/
Share on other sites

Just to clarify it will sort of stutter and shudder especially if revving or attempting to drive. Depends if u have it at low or high revs, which makes no difference except seems to have less chance of cutting out as frequently... but still stutters hardcore. If the car has been left alone for a while this can take a little while to happen. But It WILL cut out as a result of this, sooner if you "try" and drive it.

if you leave the car for a while, ie 30mins + it will start and rev ok but still sutter and choke a little bit... the longer you keep reving it the worse it will get until it gets so bad even if you start it it will die straight away. But the longer you leave the car it seems the longer it will take to get to such a problematic state. make no mistake though, the car is essentially useless.

Thoughts??

Edited by Xizor

If the car has been off for a while u can usually start it and rev it hard for a bit and usually only notice slight stutters in the engine/revs but it will progressively get worse and more frequent until it reaches the point where it will die as soon as u start it no matter how you try and rev it.

Search for how to throw the R33's ecu in to diag mode. It will then output any faulty sensors. Hopefully. :D

The fuel and afm check you may not be able to do by the sounds of it... Might be worth dropping it off to some one who knows these cars as no doubt they will find the issue quick smart.

Mate i cant drive the car anywhere really and ripping the ECU out is a bit of a last resort hehe

I'll run some diag software on it via laptop tomorrow afternoon and try and replace fuel pump and see how we do.

Anyone know how to drain fuel tank? That might be worth doing too.

What good is putting it in diag mode? doesnt it needed to be hooked up to a nissan computer or something??

I dont even care about cost anymore i want it working.

Nope, you throw it in diag mode and it runs its tests and throws out a code (by flashing a light (dash light or light on the ecu). You count the flashes and then compare the number to that in a list. It then may show something like code blah... coolant temp sensor or code blah afm etc etc..

You can even throw it in an o2 test mode where it flashes the light as the o2 sensor goes high/low. An easy way to determine if your o2 sensor is shagged, lazy, or not.

i had a problem with my RB20. all stock except an exhaust and pod. it would start and run fine when it was cold, but once it warmed up it would just cut out, altogether, then not start again for a while until it cooled down. I found the problem to be my alternator/power supply. Might be worth checking.

does the engine kick over every time you start it? either hot or cold?

Yes. But if ive had the car on for a while reving long enough or attempted driving it it will reach a point where it will cut out as soon as its kicked over. almost as if its using fuel thats flowed through due to gravity but ran out. ignore me lol

It doesnt normally just straight cut out due to temp, it struggles and hiccups like a dirt bike with its fuel ratio/mixture wrong except will also cut out like its not getting fuel and then just not go at all. then repeat process after a while.

Edited by Xizor

yeah rob thats why i said i would pick up 2 filters, one for mine and one for yours. The whole thing ith the gtr filter had me wary, i was going to swap mine in the other night but pefer daylight. and als your brother is a tool lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
    • Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
×
×
  • Create New...