Jump to content
SAU Community

Recommended Posts

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

oi mitchy if you buy one ill install it in for you :sick:

i did mine a few weeks ago and got it working the other night its sooo.... mad :P massive flames

dont think it will be good for the car though :)

simple as 4 wires but theres 2 wires that are meant to be the opposite to each other :S

Ive had one for about a year and used it on the street and the track

most people wire them to the handbreak for launch.

but I wired it to a clutch switch, basically it means I can keep my right foot on the floor, when upshifting, I just clutch in, limiter kicks in and cuts the revs down to 4500 or whatever, drop the clutch and be right in the powerband

whether its a benefit or not I dont really know, I dont think its nessesary

but its fun :sick:

what concerns me is whether it will cause damage to the turbo.

Ive got a nice expensive one going on and the last thing i want to do is destroy it.

Edited by midnight
  • 4 months later...

huumm okay umm please confirm this statement..

the Bee*r rev limmiter cuts the eart so random spark drops out..fuel goes out cylinder ignite and kaboom through exhaust turbine and cat...

there are 2 triggers one is the red line and the other is either handbrake or clutch.... so if I hit redline it went kaboom booom boom..

If I connect to handbrake, the moment the handbrake is lifted during driving..also kaboom boom boom..

if connected to clutch only when sudden clutch release at launch, launch control? went kaboom boom boom...

downside, damages everything in the flame's path....However this system shouldn't be too damaging unless one were to do launches and red lines everyday?

cheers

could the bee *r rev limiter do any damage to ya engine?

A friend of mine had one of these REV limiter on his 11sec street tyre REX, i think it was a UNI CHIP one. Anyway, he used for around 6 months and his pitston rings got damage BECAUSE of the REV limiter action so he got rid of it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Adjusting the idle screw is usually (emphasis on usually) just covering up deeper issues. Stuff like the cold start valve not closing properly. Throttle shaft seals on the way out. Coolant temp sensors getting out of spec. Coolant temp sensors especially can be a bear to diagnose because they can fail subtly. My dad just spent weeks chasing down his high idle. He cleaned the coolant temp sensor and everything but the resistance curve just drifts over time and if it's been 20+ years they also get super slow to respond as well. Has a massive effect on fuel economy as if it's off the ECU is going to run richer and command high idle for far longer than it should otherwise.
    • How old is the battery, it's more likely your battery is on its way out.
    • I reckon you'd get 90% off. My washer doesn't get between spokes very well. Haha! I love my Gerni!  Argh! Steam cleaning has its place for sure.
    • Hey all, I did a voltage test with the car (video attached) not running for 3 days. And here is some interesting stuff: - Battery voltage is 12v (I had the key in the ON position) - Drops to 9.76v while cranking then quickly goes up to 14.5v - You will notice there was a sorta slow start but not as slow as it usually is. - Idle surprisingly was better at just over 1,000rpm instead of 1,100 rpm. - I turned on the A/C, radio and headlights in the video and the voltage remains the same - I haven't cleaned the grounding wires on the chassis yet, that's next. - Battery drops to 12.6v when I turn off the car and wait a bit Seems like I might have a parasitic draw? I do have an immobiliser system which does drain the battery more of course but was wondering if there is anything else I should be looking at fixing? Does the ground wires on the chassis have anything to do with the low 12v?        SAU.avi
    • My lord that is some low oil pressure as minimum in the manual! I guess the big part will be seeing how it changes as the engine gets more spirited use.
×
×
  • Create New...