Jump to content
SAU Community

Low Boost Pressure

Guest Lojikl

By Guest Lojikl,
in Western Australia

 Share

Recommended Posts

Guest Lojikl

Guest Lojikl

Posted
Posted

Okay this has been bothering me for a while.

My boost pressure seems fairly crappy. Even when I hammer the accellerator the boost NEVER goes above about 3.5 on the standard boost guage, and I can feel that theres not much jump in acceleration.

I have a Pod filter and 3 inch cat back exhaust. My old 180SX used to hit 15 no worries,

Anyone have an ideas what might be going on here.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/13983-low-boost-pressure/
Share on other sites
rob77 Veteran

rob77

Posted
Posted

If you want to increase the boost there are 2 way, bleed valve or an electronic boost controller. Some EBC's have a boost gauge built in (blitz dual sbc) which will tell you how much boost before manifold. The bleed valve is much cheaper but will spike so you'll need to get yourself a seperate boost gauge to read what boost you are running. Eitherway is effective, just dont run more than 13psi through the stock turbo. Plus if you still have the stock intercooler you wont be able to run that boost all the time without having some detonation when the temperature is warm. Comes down to how much you want to spend and how reliable you want it to be.

rob77 Veteran

rob77

Posted
Posted

Nothing like setting my EBC to 12psi on a cold night like tonight and giving it a good fang on the way home from some crappy training session at telstra ;) Even with the stock cooler on a cool night like tonight I found I could run 12psi without much problems but with the front mount now it does seem to pull a small amount harder.

DCIEVE Mentor

DCIEVE

Posted
Posted

my r31 only reads around 3psi on the stock guage as well, fitting a better boost guage soon to suss it out.

rev210, in saying thats normal is the factory guage out or is the car just running bugger all boost?? cheers mate

rob77 Veteran

rob77

Posted
Posted

with the stock intercooler and 12psi on a 30+ degree day the car would detonate when pushed hard because the intake temps were so high, detonation sounds like a rattling noise coming from the engine and will cause severe damage to the engine if you keep pushing it, if you hear it stop pushing the car and back right off. Now I can pretty much run 12psi on a hot day and push it hard without too many drama's but I dont like to.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • dbm7
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By dbm7 · Posted

      For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
    • PotatoCake
      Exhaust silencers/varex exhausts

      By PotatoCake · Posted

      I’m also conscious that e85 is slowly being phased out. Not all United’s have them anymore. Can’t take the risk of being low on petrol and assuming the servo will have it. 
    • The Bogan
      NC MX5

      By The Bogan · Posted

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
×
×
  • Create New...