Mackay, Qld, Australia

[morto86]

Hey guysmoved to mackay 3 yrs ago bought a r32 gtst with a blown motor. Replaced motor but got mega issues. In the deep end for sure now but love the car cant wait to drive it when its going

[The Mafia]

Hey guysmoved to mackay 3 yrs ago bought a r32 gtst with a blown motor. Replaced motor but got mega issues. In the deep end for sure now but love the car cant wait to drive it when its going

Hey mate, welcome.

If you need any information, most people following this thread are very knowledgeable.

[morto86]

Hey guys I have a problem. Replaced a blown rb20det with another. The new motor arrived with the timing out by 4 teeth. We re did the timing and got it running. But it is idleling rough as guts and the motor will die without throttle. If I give the throttle a tap it jumps up but then will go out of control. Up to 3 Grand then slowly comes back down. I have checked afm iac and cold start valve by unplugging them to see if I get a response. Which I do. I have power and signal going to all injectors and coil packs. All cylinders fire. The ecu has a ewad out of 55 which is no faults. Im out of ideas. Will do a boost leak test tomorrow with soapy water. SO CHEAP! Thanks in advance guys

[The Mafia]

Hey mate, seems like you have most of the bases covered. Usually the best way to test for leaks is to pressurise the intake.

If you are handy with a welder, weld a compressor fitting onto a piece of pipe with a tap, and weld the end shut. Them simply remove your AFM and clamp it there and slowly crank the pressure up to 30psi.

It is by far the only accurate way to find leaks.

[morto86]

Hey guys did a pressure test on the intake and I have a blown plenum gasket  the supplier I bought it off has a start up warranty on the motor the fact that this was already present has asked for a quote to fix and get the motor running. Lesson: warranty is awesome

[dysonest]

Hey guys did a pressure test on the intake and I have a blown plenum gasket  the supplier I bought it off has a start up warranty on the motor the fact that this was already present has asked for a quote to fix and get the motor running. Lesson: warranty is awesome

looks like ur lucky there mate

[89CAL]

After a new clutch cylinder for my car. (P/N: 30620-21U23)

Going to try Brakemart, Repco and Bursons, but just putting this up in case these fail and anyone has one lying around

Its a 3/4 Nabco slave, believe they might be the same as R32 ones, but not 100% sure

Hopefully should be able to source a new one anyway

[t5iv]

Do you guys buy parts from Repco regularly? If you're a financial member of SAU QLD, you can get 10% off and once a month they do 30% off.

[89CAL]

Really? I dont go there that often. And I always forget to use my racq card anyway lol.

Ended up getting my slave honed and re-sealed by Better Brakes. They had it done in about an hour as well. Looks all shiny and new now

Works as well which is a plus

[morto86]

Didn't know they did that at better breaks. Good to know. What did it set ya back

[89CAL]

They were originally going to re-sleeve as well but said the bore didnt end up being that bad.

was just shy of $50, noone seemed to stock a new one. Was about to try nissan but dare say it would have been $100 plus

I don't think a re-sleeve would have cost much more, said it was going to be stainless re-sleeve so should last longer, but I'm happy as with the result. Like I said, looks like a brand new one after they sand blasted and re-kitted it

Have a funny feeling it might drive again tomorrow

[morto86]

Top shelf lad

[89CAL]

Having fun tidying up vac lines and wiring >_>

[Seano350GT]

http://www.carsales.com.au/private/details/Nissan-Skyline-1999/SSE-AD-2492740/?Cr=3&sdmvc=1

DROOOOOOOOOL!

[89CAL]

I quite like 34's in yellow

get the wallet out Sean and just do it

Get the impression that this is really well looked after as well, has only been lightly modded. Would be a good one

Edited December 6, 2013 by 89CAL

[t5iv]

http://www.carsales.com.au/private/details/Nissan-Skyline-1999/SSE-AD-2492740/?Cr=3&sdmvc=1

DROOOOOOOOOL!

If you're buying a BNR34 fro Qld, let me know. I know a few of the Brisbane bmr34 guys and they can give me the down low on the car.

[slo 10z]

Yeah buy it Sean....

[slo 10z]

Anyone from Mackay know forum member drag-on Silvia?

[The Mafia]

Anyone from Mackay know forum member drag-on Silvia?

Name rings a bell, know their real life name?

[slo 10z]

No he/she from Townsville.... He/she is selling a turbo I interested in