Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

I used to run Mobil 1.

BUT, just as a treat one day and I liked the name I tried Royal Purple, there is no point in trying to sell it. You just have to try it yourself and see the results. I couldn't believe that oil would make such a difference.

Link to comment
https://www.sau.com.au/forums/topic/14-oils-aint-oils/#findComment-232
Share on other sites

  • 3 weeks later...
I used to run Mobil 1.

BUT, just as a treat one day and I liked the name I tried Royal Purple, there is no point in trying to sell it. You just have to try it yourself and see the results. I couldn't believe that oil would make such a difference.[/quote:fd1587d658]

i've heard nothing but praise about the royal purple. it's on everyones top list so it must be worth it. i think i'll try it in around 2000k's when my service is due.

peakRPM, how much do you pay for 5L?

Link to comment
https://www.sau.com.au/forums/topic/14-oils-aint-oils/#findComment-233
Share on other sites

There are about 3 different "grades" of Mobil 1. I'm not talking about the viscosity but the actual quality.

This was news to me a couple of weeks ago. I have been using the 0W40 I get from my Bro in law. Cost price is now $16/litre, used to be around $10. It's good stuff. It's not the same as the stuff you get at K-Mart.

The car blew some tiny puffs of smoke when it 1st went in but now doesn't blow/use any. Thin as water. I change it every 5000 or earlier (usually 'cos I can't quite remember when 5000 is up...)

Recommend it.

Link to comment
https://www.sau.com.au/forums/topic/14-oils-aint-oils/#findComment-234
Share on other sites

In an engine like the RB25DET I think the thinner the better. Nissan engines typically use a fairly thin oil anyway (normally around a 5W I think). Their tolerances seem pretty tight, so the thinner the better especially with the turbo.

In the bike I use a thicker oil (straight 40W or 50W) as it's air cooled and these engines naturally have wider tollerances. If you have an old clunker and it's using/blowing oil try a thicker viscosity.

Whatever you do keep that el Cheapo no name stuff out of your engine. Buy the best you can afford.

Link to comment
https://www.sau.com.au/forums/topic/14-oils-aint-oils/#findComment-238
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...