Jump to content
SAU Community

Wrecking R32 Gtr - 1994


Recommended Posts

Hey Guys,

I'm parting a R32 GTR 10/94 with 71000 km's. It has been smashed in the left hand rear, with slight front left damage. The following parts are available, although in case I missed any, please call. Car is complete MINUS ENGINE. Willing to seperate everything else

PLEASE CALL 0410 664 336. DO NOT PM - I RARELY GET ON THE NET.

All parts located in Sydney - AGAIN PLEASE CALL, DO NOT RESPOND HERE OR PM.

a/c compressor - $200

power steering pump - $100

front tein height adjustable suspension - $ 400

various suspension components available - Call me with what you need

radiator and shroud - $250

side skirts - $250

interior - Willing to separate

gtr rear wing - $250

right hand tail light - $100

boot garnishes - $70

rear bar (fair condition) - $150

rear diff - $400

front diff - $200

factory airbox - $180

clutch master cylinder - $80

right hand rear disc and caliper - $100

washer bottle windscreen bottle - Make an offer

front and rear wipers - Make an offer

stock blow off valves, factory intercooler pipes - $250

horns - $35

dash immaculate - $400

brake master and booster - $150

parcel shelf - $50

side mirrors - $120 both

front brakes and rotors (slotted, near new) - $700

gtr fuel pump - SOLD

windscreen inbuilt antenna - SOLD

tail shaft - SOLD

a/c condensor & bottle - SOLD

front seats - SOLD

rear quarter window both sides - SOLD

r/h headlight and blinker - SOLD

bar support - SOLD

r/h guard - SOLD

bonnet - SOLD

doors - SOLD

front grill - SOLD

factory rb26 injectors & resistor - SOLD

abs unit - SOLD

drive shafts - SOLD

rear trims - SOLD

gearbox - SOLD

post-2747-1165133171.jpg

post-2747-1165133181.jpg

post-2747-1165133192.jpg

post-2747-1165133202.jpg

post-2747-1165133214.jpg

post-2747-1165133225.jpg

post-2747-1165133234.jpg

post-2747-1165133244.jpg

post-2747-1165133256.jpg

post-2747-1165133265.jpg

post-2747-1165133278.jpg

post-2747-1165133292.jpg

post-2747-1165133324.jpg

post-2747-1165133337.jpg

post-2747-1165133347.jpg

post-2747-1165133358.jpg

Edited by MrFlex
Link to comment
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guys,

This is straight from an RTA enquiry:

" a vehicle classified as a repairable write-off means that it can be

re-registered in NSW. In addition to the below requirements, evidence

of restoration will be required. The vehicle may also require further

inspection.

The most up to date and current information regarding registering

your vehicle in NSW can be found using the following link from the

RTA website: -

http://www.rta.nsw.gov.au/registration/rego_new.html "

So looks like if anyone is willing to repair the shell, it can be re-registered.... Parts also updated. Call me on 0425 339 737 for any queries

Cheers.

Edited by MrFlex
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Pretty simple question. I was about to put the transmission back in and thought I pretty much had it lined up when I noticed it seems like the pressure plate isn't flat. I was pretty careful when undoing the bolts both during initial disassembly for cleaning and when torquing them up for installation so this is pretty discouraging. I'm not sure if I accidentally bumped the pressure plate with the input shaft and bent it somehow or if it just showed up this way. Is it possible that there's just something obvious I'm not doing correctly? I'm pretty sure I was extremely careful to make sure the friction discs were seated correctly in the hub, everything lined up, flywheel torqued according to sequence, the little springs all sitting correctly in their seats, etc.  What's the play here? Do I jump straight to a new pressure plate?
    • OK. I can see that being the case. But if you live in the land of "only switching between 4.08, 4.11, 4.36" like most Skyliners, then you never encounter it. Now I perhaps understand why the crownwheel is thicker on some of the smaller numerical ratio diffs. The two stubs being the same (unequal) lengths and just swapped side to side between the different cases is a new one to me. I'm hating Nissan R200s more than ever now.
    • Reason I say this is I have seen broken ones, in drift, drag and even behind a stock Z. I do appreciate most of the time its the synchro's that go.   Trouble with quoting HP is it doesn't really say how strong the box is.  I've not seen many CD00X box's make it past a mid 9(150mph) I have seen about a stock R33 RB25 box's run a 9 too, they all go boom at some point though.   Another clue is they make gearsets for CD00X box's too, wouldn't be a market if they didn't break or have a limit people are going past.   I totally agree it is a strong box, just have to weigh up the true total cost of the conversion vs rebuilding with a good gearset. 
    • What makes you say CD009 boxes are not as strong as you would think? I've always been told the last revision (CD00A) is good for 1000whp and I have no issue's believing it when comparing one side by side with an RB25 box. Makes them look tiny. 
    • I picked up an open Center with shafts. I was told the Open shafts will fit a mechanical LSD and looking at them. I think they will work. Will update 
×
×
  • Create New...