Jump to content
SAU Community

Recommended Posts

I have a fujitsubo 3inch cat back and it sounds good.But all other skylines i hear sound angrier and throatier,not to mention louder. Why is this? Will a dump/front pipe make my car sound better? Im after the cool RB sound that is unmistakable. Anyone got any suggestions?

CHEERS

Do you have a cat?

Ans:

NO: Then probably make no differance

YES, but std:This will be drastically restricting flow, thus will be suffocating engine and robbing you of power.

I myself use a legal hi-flow cat.

My car gets very angry in traffic and yells its head off when it finally breaks free.

I like the noise but the resinating in the car sometimes gives me a head-ache.... ;)

If you want load and angry.....straight through custom 3" pipe and hot dog with no silencer.

If this is too load get a 3"resinator put on like me.

;)

Mine was just a split dump, cat then straight through to cannon.

I had to have a resonator added , the drone in the cabin was just far too unbearable. When you hit the right rpm the whole cabin would just vibrate.

No not yet but wouldnt that make it quieter?

In all probability, no.

Most mufflers work by slowing down the exhaust gas. Taking energy out of the exhaust stream reduces the noise it generates when it exits. I'm sure you've noticed that most aftermarket exhausts that are less restrictive also tend to be louder than stock.

If the cat is less restrictive to flow, its also muffling less.

I had a JASMA certified Fujitsubo cat back with centre muffler/resonator and final oval muffler with standard dump/front/cat and it was also noticably quiet when putting arond but had a deep clean note when opened up. Anything but a bark. You'll notice a lot of the cars you see with a "bark" are NA.

Dont know about other aftermarket Jap systems but what I noticed with my Fujitsubo system was that it was extremely heavy due to the fact that it was extremely thick steel, which I think helped quiet it down. I reckon it would of been 3mm thick, if not more easily as it had a decent chunk taken out in one part at least 2mm deep and it had not made close to a hole.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...