Jump to content
SAU Community

Recommended Posts

Anyone had a similar experience on a 32, Gts-t, no that it matters really caus its definately an interior item making the noise (I THINK), and they are more or less the same.

Anyway, evcerytime i find a pothole in the rd (Adelaide roads are shocking so this happens many times), it sounds as if something towards the rear seats or speakers etc rattles, ive checked the seats and they seem to be down firmly (i got a seat rattle ages ago but fixed that all up) but now there is another problem.

Anyone had anything similar happen????

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/
Share on other sites

otherwise open the boot, and on the passengers side under the carpet there is a hole (where some cars have their jack). check down in there. i pulled out a matchbox car, some makeup, and a few other random pieces of junk from previous owners.

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/#findComment-2628559
Share on other sites

yeah i initially went down this rd...but then found nothing but a tool kit (factory one) and thats about all...shes all clear now. I think im going to have to get someone to check...could it be any of my bushes being farked and causing excess noise?

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/#findComment-2629579
Share on other sites

Worn bushes can make a variety of noises, tho usually a knocking noise depending on which bush it is. Get under the car and go over all your bushes with a torch and a pry bar making sure you flex them enough to see any cracks or sloppyness.

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/#findComment-2630951
Share on other sites

Worn bushes can make a variety of noises, tho usually a knocking noise depending on which bush it is. Get under the car and go over all your bushes with a torch and a pry bar making sure you flex them enough to see any cracks or sloppyness.

I had a similar rattle over bumpy roads from the parcel shelf area of the rear of my r33 gts-t , turned out it was loose top mounts of the rear suspension struts , which mount in the parcel shelf area (a bugger to get to as well!!!!!).....easy to tighten up once you get to them....

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/#findComment-2636992
Share on other sites

otherwise open the boot, and on the passengers side under the carpet there is a hole (where some cars have their jack). check down in there. i pulled out a matchbox car, some makeup, and a few other random pieces of junk from previous owners.

lMAO who stores makeup in a hole under the carpet in the boot? was it a white powder?

Link to comment
https://www.sau.com.au/forums/topic/140898-annoying-noise/#findComment-2650657
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
  • Create New...