Jump to content
SAU Community

Recommended Posts

:D

HI. ive got an R33 and for the last 8 days ive been having probs with excelleration. When i take off the car feels like it is pulling back. It is really hard to get ay boost and when i do it comes in dangerous short bursts. I thought it my be fuel tampering (scabby servos) so i let it run dry and went to anoher shell but its still happening. I'll be drving and will try and put my foot down and get no power then all of a sudden, i get, as i said, a shor power intake and it is quite dangerous cause it will happen when im right behind another vechile.

So if anyone out there has any suggestions i would more than appreciate your help as im so worried about my princess....

Thanks in advance

Gem

Edited by princess01
:sick:

HI. ive got an R33 and for the last 8 days ive been having probs with excelleration. When i take off the car feels like it is pulling back. It is really hard to get ay boost and when i do it comes in dangerous short bursts. I thought it my be fuel tampering (scabby servos) so i let it run dry and went to anoher shell but its still happening. I'll be drving and will try and put my foot down and get no power then all of a sudden, i get, as i said, a shor power intake and it is quite dangerous cause it will happen when im right behind another vechile.

So if anyone out there has any suggestions i would more than appreciate your help as im so worried about my princess....

Thanks in advance

Gem

I had similar problems with my last car (silvia turbo). Cleaning the air flow meter helped (take it out, run some metho over the element that sits in the middle of the afm (do NOT touch any wires with your fingers), let it dry fully then put it back in the car). Not sure what the problem was exactly. It seemed to do it more in hot weather or after the car had heated up a bit.

The reason cleaning my afm helped was because I was using an oiled air filter (k&n) and they tend get oil all over the element in the afm. I changed back to a dry air filter and had much better results. Cant say if the afm was the problem. I suspect the problem may have been elsewhere and just made worse by the afm reading incorrectly.

Other suggestions might be to check the fuel pump?? dunno.

Does it seem to accelerate ok up to when you'd hit boost? Does it stutter or just really bog down and you get nothing? In my case the revs would build up slowly and it would seem to pick up a little but it was terrible. And only after 15-20 minutes or so of driving. Often I could turn the car off then back on and it would be fine for a couple of minutes.

Hi, It might help if you list any mods (if any) on the car that you are ware of.

One of my mate's personally imported a series 6 RX-7 & it ran like crap because it was tuned in Japan to run on their premium fuel (108ron?). A simple re-tune on the dyno fixed it right up & it runs beautifully now.

has the car been previously owned in australia or are you the first owner?

Good luck with fixing your car & hopefully someone on here has an answer for you.

Hi, It might help if you list any mods (if any) on the car that you are ware of.

One of my mate's personally imported a series 6 RX-7 & it ran like crap because it was tuned in Japan to run on their premium fuel (108ron?). A simple re-tune on the dyno fixed it right up & it runs beautifully now.

has the car been previously owned in australia or are you the first owner?

Good luck with fixing your car & hopefully someone on here has an answer for you.

Hi,

There are no mods at alll on the car. It was owned in aus before me. Thanks for the advice. Ill give it a go

So... when you give it half throttle, it stutters? Or it drives normally but with no boost? When the boost comes on, it shouldn't launch you TOO hard on a stocker. What does the boost guage read when all this happens?

How far are you putting the boot in?

If it IS just the boost, and not a fuel or coilpack or whatever problem, then maybe you have a sticky wastegate actuator? You'd have to be gunning it and not just normal traffic driving to generate that much boost that you feel it though.

she did say it happens when shes taking off so its not the common misfiring problem.

it could be your:

CAS

AFM

spark plugs

coil packs.

do the spark plugs if you havent already. take your AFM out and spray with carby cleaner. do my coil pack fix, and try swap your CAS with someone else with an r33.

if you can get your hands on someone else's CAS, then do that first.

if you were in syd i'd be able to give you a hand.

Sounds to me like misfire

Does it happen around 4000/5000rpm onwards?

hi ta for your suggesstions. i took it apart and it is the coils. one cover is broken. YEAH!!!! not the thousands of crap that i thought it may be:)

ta gem

Check sparks, check coilpacks for hairline cracks, clean afm?

Does "sound" like the common missfire problem that nearly every line owner has.

hi ta for your suggesstions. i took it apart and it is the coils. one cover is broken. YEAH!!!! not the thousands of crap that i thought it may be:)

ta gem

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
    • You can get them with the worm drive rotator but I was too tight to pay another $250-$300 so manual labour it is! I don't think it will be too hard to rotate though. 
    • Sag as in the windows start to slowly open themselves, or they're just slow to go up/down with engine off?
    • It looks like it needs a big worm gear drive on it to control the rotating, not a few sloppy pins!
    • As Duncan said, first there was OBD, which few cars used, then came OBD2.   Now an interesting point, OBD2 isn't even for what you want to do. OBD2 is for emissions testing. There is some sensor data on OBD2, but it's up to the manufacturer what they're putting on it. Most scan tools operate on UDS, which like OBD2 is a standard built on-top of CAN. UDS specifies how to structure a message, what very limited things mean such as "read memory address" but it does not specify what is stored in which memory address, that is all up to the manufacturer. You either a scan tool compatible with that vehicle, or to know how to reverse engineer all the data, which can take a VERY long time and a lot of vehicles to get it right. Oh and then the manufacturer does a firmware update and changes what's where... Ask me how I know that as fact Oh, and by the time you've got the scan tool that supports all the manufacturers stuff, well, you're back at "But a consult cable and the Nissan software" The main difference being most manufacturers software these days works with the same hardware readers, as the readers are built to support J2534 which is another standard for how the PC communicates with the tool to make it do specific things on the car...
×
×
  • Create New...