Jump to content
SAU Community

Recommended Posts

I've been looking @ getting my air conditioning regassed, the car is s1 r33 gtst

the air cond. currently works, just takes a little longer than it should to get cold.

I've heard that it may just need a top up? or regas which apparently should be done

every two years?? They also recommend changing the filter too.

I don't know whats involved, but if it already works, i was told to allow $250 for regas

This sounds over the top?? :no:

Has anyone has a basic regas and would be able to advise on price

and maybe recommend a place in Adelaide to get this done.... Cheers :)

Link to comment
https://www.sau.com.au/forums/topic/141378-air-conditioning-re-gas/
Share on other sites

I got my air re gassed not long ago, they had to change the fittings which was baisically screwing an adaptor on the original fitting which they charged an extra $60 for (saw me coming) and the total bill was 150, this was in tas tho.

i had mine done 2 weeks ago (trying to avoid the summer rush) :) cost me $150, however i opted for a coloured dye (cost that little extra) which is handy for future to find a leak.

on my drive home barefoot, my clutch foot went numb! like seriously cold - put a digital thermometer in the footwell and it was 9ºC!!!!

so if my aircon is fairly cool, but not freeezing cold, will a re-gas correct this?

and what's the deal with the filter? i'm not familiar it.

Yeah id try topping it up first, thats what i plan to do with my aircon.

And the filter, i know in quite a few airbox's they put an airfilter inside to trap dust and leaves and all that crap, could be something like that. Or it could be a filter somewhere in the lines or condenser or evaporator.... not sure where though, and what it would do since the ac is really a sealed system.

i had mine done 2 weeks ago (trying to avoid the summer rush) :D cost me $150, however i opted for a coloured dye (cost that little extra) which is handy for future to find a leak.

on my drive home barefoot, my clutch foot went numb! like seriously cold - put a digital thermometer in the footwell and it was 9ºC!!!!

what did u get done? just a re-gas (with dye)? or filter etc aswell?

what did u get done? just a re-gas (with dye)? or filter etc aswell?

no - just a regas.

however i do have to go see him within the next few weeks so he can check if its leaking - said that if its leaking he'll change over the entire canister with fittings for free, if not just leave it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...