Jump to content
SAU Community

Recommended Posts

  • Replies 147
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

^^ yep, those all have to be fuel resistant.

when i did the pump in the R31 I put some ordinary closed-cell foam in as a spacer, and the petrol destroyed it in very short order. if I was doing some custom work in the tank I would cut off small pieces of what i wanted to use and soak them in petrol for a week to make sure they didn't dissolve.

sweet setup though, well done B-man :ermm:

Did you have 1 or 2 Duncan ?

Fuel pressure is base - no aftermarket reg

Had to put a check valve on the line just out of the tank as the ones that are allegedly on the Walbros don't work very well - apparently this is common.

  • 2 months later...

So far so good with the Walbros - 45 PSI idle fuel pressure - goes up to 60 when boosting. Not a problem at all.

People seem to love them or hate them the Walbros - the Yankees love them - They flow well, draw less current, have a small form factor - thus in tank fittment of two is not a problem. And they are in-expensive compared to some others.

So - just an update on where I am at with the Cosmo now.

After sorting thru some small issues - Fitting a 4.5" exhaust, new mufflers, re-tune etc - am now at 340rwkw (that's with the auto so engine HP would be close to 400 or so. And that is running 10PSI

Boost starts at 2300RPM, 5PSI by 3000 and Full boost 4000RPM all the way to 8200RPM (nice power band from 4K to 8.2K) Power climbs and climps and is still climbing at redline.

Boost will be going up soon - to 15 PSI. (Need new 3 bar MAP sensor and complete retune - bugga) So hopefully over 400rwkw

I have a MV Stage II built box coming with a 3800 RPM stally.

10s here I come :P:D:)

I took the return fuel line off while on the dyno (Ok Ben at UAS did it but I watched :P) and at 255rwkw the flow completely stopped. Scary stuff. Also had major issues with fuel pressure which went away once I put an R34GTR pump in there.

As you say though, some love em and have no problems and some love em.

It's a MUST to run a dedicated relayed circuit from the Battery for these pumps. They don't voltage step well.

340rwkw - my 1600cc/min secondaries are running at 20% or something - no fuel problems for me

You also gotta ensure you get Genuine Walbros - there's China copies out there that are shite.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
    • What are your thoughts on this after having it for a while, worth getting?
    • Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...