Jump to content
SAU Community

Which Boost Gauge?

Noel

By Noel,
in Engines & Forced Induction

 Share

Recommended Posts

heller44 Mentor

heller44

Posted
Posted
i bought an "autogauge" gauge from "online depot" also for pretty cheap

they provide a good product for cheap, but there is a couple of weeks delay with them..

worth it for the price you pay :whistling:

I'd use a different quote.. "you get what you pay for."

Like a few people in this thread, I bought a black face autogauge meter from the same place.

Prompt delivery and the product looked alright. Hard to see the needle in daylight though.

After a couple of weeks I was bothered by the rest position of the gauge ( reading when engine was off ) plus it was reading about 4 psi on stock gtr actuators.

Scavenged a mechanical test gauge from work and used it as a reference.. was sitting on about 9psi.

Meter was filed in the round filing cabinet..

Ordered an a'pexi mechanical el meter to replace it and am much more confidant of a correct reading.

I wouldn't consider a correct reading gauge a luxury.

James.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Noel Community Regular

Noel

Posted
  • Author
Posted

quick question regarding install

comes with a long length of clear tubing which you attach to rear of gauge then run into engine bay, then there is a short lenth of a larger size tube which you attach to t peice from vacuum line...should i just use the smaller sized tubing all the way or buy some more tubing the same size as t-peice & run that all the way into cabin then use a tiny amount of the clear tubing just to attach to rear of gauge?

Thanks

Noel

Noel Community Regular

Noel

Posted
  • Author
Posted (edited)

Ok installed gauge on weekend...I put it where the ashtray is supposed to be...Just took it out, cut a bit of mdf to fit then cut out hole in middle for gauge, stuck some grey carpet that i had lying around on, put gauge in mdf, it hooked it all up then pushed mdf into space & presto i now have a boost gauge in a legal spot...will post pics when i take some.

Only drama i had was a tiny one where T-peice did not fit original vacuum hose to inlet but i replaced this with left over 4mm hose that i had used instead of the clear nylon tubing that comes with gauge & was all good

Edited by Noel
d00dz Grand Master

d00dz

Posted
Posted
Ok installed gauge on weekend...I put it where the ashtray is supposed to be...Just took it out, cut a bit of mdf to fit then cut out hole in middle for gauge, stuck some grey carpet that i had lying around on, put gauge in mdf, it hooked it all up then pushed mdf into space & presto i now have a boost gauge in a legal spot...will post pics when i take some.

Only drama i had was a tiny one where T-peice did not fit original vacuum hose to inlet but i replaced this with left over 4mm hose that i had used instead of the clear nylon tubing that comes with gauge & was all good

Here are some pics I took yesterday, with my new camera, of my dash/center console:

Ricey I know lol

Click here for more pics

Center_Console_Liteup.jpg

Dash_Liteup.jpg

Noel Community Regular

Noel

Posted
  • Author
Posted
Its been sent but Aust Post dont know where it is...Mark is chasing it up with them

Received, seems Australia Post magically found it, & it showed up at reception once we enquried about it.

All good its here now so now i can go and play ;-)

Also my turbotech does not have a little pin hole in it...in the original thread for these i saw a few others also had no hole & one was even told its the new design...is this a problem or is it all good?

Cheers

Noel

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • luke gtr
      Another little story of weird shit happening

      By luke gtr · Posted

      At least you're now aware of the problem and can come up with a solution. 
    • luke gtr
      So i brought a boat...

      By luke gtr · Posted

      Dang. Keen for further updates when you get to it.
    • Duncan
      New Stegea Owner

      By Duncan · Posted

      Welcome to SAU Thomas, sounds like you'd had a bit of a an unlucky start with the car, hopefully you get some better luck now!
    • Duncan
      R34 gtt rb25det neo timing belt kit

      By Duncan · Posted

      1. No need, it only gets used once then is locked in place by the nut 2. EN-62 point 6 shows the conical washer the other way around (BTW I know we discussed above, I hope you are changing the idler as well, while it is no guarantee the bearing is a actually bad, it looks terrible) 3. I'm not really clear on the question, are you worried because it was easy, not hard, to remove the custom timing trigger? As long as it doesn't spin on the crank (when the bolt is tight) all good 4. Yeah just make sure the brand is easy to read as it rolls past 5. The part number is on the listing under the description, 13023-42L00. Given there is a custom part on there for timing (presumably outside the cover), they may have decided to leave that off; I think I would put the washer in there as it also helps seal the timing case from crap getting in.
    • thomasLait
      New Stegea Owner

      By thomasLait · Posted

      Hey everyone, I recently bought myself a 2001 Nissan Stegea M35, and I've had a few issues that I had to fix, my car would start intermittently and I had a bad rocker cover leak, after a couple days of looking I finally found a part number that interchanges with the OEM starter as the OEM starters at $1300 and I can't afford that, this starter was only $270 and I replaced the start and still had the same issues, I posted a video asking for help online and it went very well, some guy said it was probably a bad ignition switch so I took my dash apart and turns out my ignition switch was half screwed in and was loose, once it was tightened it fired right up, I found a local place called "Boost factory" and they sold me a part of OEM Nissan rocker covers, they were $600 which was a shocker but I couldn't find them anywhere else, so I installed them and fixed my oil leak as the old rocker cover was cracked and warped, I now need to replace my boost air inlet hoses as they have some cracks.
×
×
  • Create New...