Jump to content
SAU Community

Recommended Posts

was fiddling with my car today and washing it aswell and when i openned my boot found two wet patches on the sides

pulled it out and noticed a nice pool of water collecting under the spare wheel.

how do i go about finding and sealing the boot from water leakage. the base is starting to build rust already so i sprayed some wd-40 stuff to try and prevent it.

all help appreciated. :)

Link to comment
https://www.sau.com.au/forums/topic/14261-leaky-boot/
Share on other sites

Guest N/A R33

The overlap joints of the panels, on both sides of the boot seal. leaked on mine. I sealed it up using sikaflex sealent don't use silicon because it is acid based and will cause rust to start.

Run a bead alonf the joints and if you wish along the joints underneath. Don't just do the underneath because even though it stops the leaking the water will still go into the joints and cause rust.

The stuff comes in white or black and can be painted over.

Steve

Link to comment
https://www.sau.com.au/forums/topic/14261-leaky-boot/#findComment-288342
Share on other sites

What he said.

It possibly is the joints along the boot 'drain' channel. It has a sealant and paint over it from the factory, but can develop hairline cracks over time (which can leak a startling amount of water).

Take it to a good panel beater and they will strip it, reseal it and refinish it for that better than new look. Should only be a hundred bucks or so from memory.

Link to comment
https://www.sau.com.au/forums/topic/14261-leaky-boot/#findComment-291884
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
    • Light should be a pressure switch, not a sensor.
    • The pressure light likely has a different sender to a pressure gauge, its been too long for me to remember for sure. Just have a look for another sender down near the oil filter. If you are confident in your rewired pressure sender reading correctly, you can be pretty sure it is just the dash light's sender failing, it is a pretty common thing.
    • It would be nice to see the result, but instagram is a click too far
    • That is a series 1 front end (grill, bumper, headlights). I'm not sure if you are trying to confirm if your whole car is series 1 or just the headlights, but the build date and vin# on the plaque in the engine bay would be the best reference for what it was when it left the factory (noting a lot may have changed over the years)
×
×
  • Create New...