Jump to content
SAU Community

Recommended Posts

60/40 more a track car

have a 4x4 for a daily

ive been told re55s are the go is anyoune running them and can you buy them in diffrent compounds as in harder/softer

Edited by spirosky33
Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2663194
Share on other sites

I personally think anything Dunlop are the best, but RE55s are cheaper and come up to temo quicker which is good for club sprints...bad if you want to do 10 more then 6 or so laps.

RE55s also dont seem to mind plenty of heat cycles. A friend that ran the Yokos on his GTR and another that runs them in the 944 Porsche series think that after a few heat cycles they are past their best, even though they may have plenty of trad left on them

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2663467
Share on other sites

The Dunlop DZ02G are the best semis I have used, the bridgestone re55 are also excellent.

I've tried a bunch of other ones but have always been disappointed in comparison to those two - yoko A032R, yoko A048r, toyo 888, falken rs04v, falken rt215, kumho 712, dunlop d01j, dunlop d98j, bridgestone re540s.

But any of them will be chewed up in 5000klm especially if you are running a bit of camber.

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2663874
Share on other sites

for 60/40 track/road use, you would probably be best off with a good road tyre designed to be used on the track sg:

Falken RT615 (treadware 200)

Federal 595RS (treadware 180)

These aren't as sticky as semi slicks but have stiffer sidewall construction than most normal road tyres.

These are the allround pick of semis. One of the cheapest, best and most common:

Bridgestone RE55S soft=WT, med=TT, hard=SR

Bridgestone RE540S soft=G, med=S, hard=R

others:

Dunlop DZ02G

Dunlop D01J

Yokohama A032R

Yokohama A048R

Kumho V70A

Toyo RA1

Toyo R888

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2664474
Share on other sites

somthing sticky but not going to be chewed awy in 5000ks?

Most / All true Semi Slicks will be all but worn within 5000kms

My advice is go for the Federal 595-RS's

I had not driven on anything but street tyres until I bought these, at a recent track day I noticed the difference in grip levels and overall confidence they gave over the old Bridgestone road tyres was massive!

Infact I dropped almost 3 seconds in Lap times.

I imagine a true semi slick would be another level up again and would be good for another second off my lap time, but the tread life they offer is not enough for me as I do not want to run 2 sets of rims.

You should comfortably acheive 15'000kms from the Federals.

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2671935
Share on other sites

RE55's are the best bang for buck I have used.

And I've tried DJO1, DZ02, RE540 and A048's as well.

Just have a set of R888's on my car now but I'm not expecting much from them to be honest (only have them because they were free).

The only tyres I'd buy however are RE55's (SR compound - which is all they'll have unless you specify otherwise)

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2673540
Share on other sites

I have used RE55S, great grip, but only got a bit over 1500kms out of them

I have also used RE540, better wear, a little less grip

I am currently running Federal 595RS, cheapest of the bunch, grip is very good, they are on my daily which sees a track at least once a month and have lasted for nearly 6 months now, and still have more than 1/2 tread left

Best bang for buck, especially for street driven car IMO

Link to comment
https://www.sau.com.au/forums/topic/142897-semi-slicks/#findComment-2674472
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok interesting i guess ill wait till using a manual gauge before making assumptions.
    • Not in any way a logical conclusion. Also, looking at those logs, I struggle to see how that much oil pressure can go away that fast unless you are sucking air into the pickup. Meanwhile the ECU voltage is chucking a huge wobbly which seems to be tied to the throttle position. 100% throttle results in decreasing voltage. It's a mess.
    • So didn't get around to installing a manual oil pressure gauge and then decided to take the car for a cruisey drive to a cars and coffee and brought the laptop along with to get another log using more gears to see if its an oil pressure issue under acceleration or after. this log has 3 gears of WOT where as previous had 2 and the oil pressure dropped once on the brakes, and the same again happens here which is interesting as it shows it can hold oil pressure while under acceleration but once slowing or just the lower RPM after a pull pressure drops. I will be chucking a manual oil pressure gauge on to confirm but so far this makes me feel it is not an electrical issue. Something else i realised is the pressure sensor also is giving temperature information and the temp stays steady the whole time which makes me feel like the sensor itself is showing a true pressure reading.
    • LOL.... fk...   there goes 25K to make 200kW
    • For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
×
×
  • Create New...