Jump to content
SAU Community

Recommended Posts

I took by rear bar off yesterday to fit a tow bar and found a little rust it hasn't done any significant damage yet and I think I should be able to fix and stop it ok.

My car is a 95 R33 GTSt 4 door with 70,000, Never bent and in visualy perfict condition.

I just thought I would let other R33 owners know about the problem so they can check there cars.

To see the problem you will have to pull the rear bar off.

1.

Remove number plate and undo the bolt that holds the bracket down.

2.

There are three nuts on the inside of the boot on both sides behind the trim and below the taillights you will need to remove these from both sides.

3.

With the boot open there are I think 4 maybe more black plastic plug type clips that hold the top of the bumper on they will need to be removed.

They are a bit tricky I tried levering them out with a screw driver but ended up having to use pincers and just pulled them up until they popped out (I only cracked one)

4. Now you should be able to pull the bar off.

The problem area

There is a upside down L shaped bracket (The one the black plastic plug clip things go into).

On my car there is rust stains that have leached down from behind this and a few bits below it where the paint is bubbling up. It looks like moisture has got in between the bracket and the back wall of the boot.

I recommend all R33 owners check this spot, before I pulled the bar off I had no idea my car had any rust. :P:D

Has any one else had this problem?

Are there any other Rust Hot Spots I should know about?

Any Recommendations on how I should go about fixing it ?

Thanks

also big rust spot

is under the spare tyre in the boot

i got a leaky boot so water has collected down there and its starting to rust

can someone help me with this leaky boot business?

its in my other thread

I own both a VL Calais turbo and a Skyline.

What’s wrong with a tow bar on a skyline?

I’m not wanting to tow a horse float just a aluminum motor bike trailer and two bikes a total of 350 kg.

Skylines can tow fine I have seen them towing boats and one with a small pop up caravan. R33 GTS-t 4 doors have a towing capacity of 900 KG

Hi Burns,

After taking the front right hand gaurd off my car, and the right side skirting, there if a gap near where the skirting is screwed onto, at the front. Which has succesfully stored about 3 handfuls of dirt / leaves for the last few months at least.

There were signs of minor surface rust, nothing major, but I am definatly glad I found it now not later :D

I'd reccomend taking the skirting off both sides and giving it a good clean. Especially at the front near the framework.

The VL is for sale

The tow bar on the skyline cant be seen any way it is all hidden behind the bumper except for the tong bit and I will take that off when not using it.

Thanks for the tip glenmcrae I will have a look while the car is all pulled apart.

The tow bar came from Nissan it is a S14 200sx tow bar and cost me $265 with all the bits and pieces.

I was also quoted $395 for a custom one.

I was told the S14 kit from Nissan will fit on the skylines fine and it almost dose the only problem is that there is a bulge in the lower section of the rear boot wall. this bulge stops the tow bar mounts from sliding all the way in to the chassis rails so I will have to have them extended about 3 inches. My car is a 4 door the 2 door might not have this bulge so it will go or piss easy.

  • 11 months later...

about the leak into the boot issue - if your car is parked on a down hill slope, water pools just under the boot lid (where it is supposed to run out, but on a downhill slope cannot go anywhere). The pooling water slowly leaks through a join in the metal. Hope that helps to explain it.

Well thats where mine leaked.

Mike

The tow bar came from Nissan it is a S14 200sx tow bar and cost me $265 with all the bits and pieces.

I was also quoted $395 for a custom one.

I was told the S14 kit from Nissan will fit on the skylines fine and it almost dose the only problem is that there is a bulge in the lower section of the rear boot wall.  this bulge stops the tow bar mounts from sliding all the way in to the chassis rails so I will have to have them extended about 3 inches.  My car is a 4 door the 2 door might not have this bulge so it will go or piss easy.

Burns,

Mate I would be very interested to see if you could take any photos to share of the tow bar on and off. Interested to see what it would like as this is something that could come definately in handy for me, and I am sure some others would be curious to see what it all looks like. Always another option and something to do.

Cheers mate!

-Alex

  • 10 months later...
Tow bars on a stock r33 turbo would be fine. But once u start playing with mods, the way the power come on aint the best for towing as u could easily rip the ass end out of the car when boost hits.

Thats exactly what I was thinking... but on a 4 door N/A R33 it would look sorta ok.

yeap under the spare tyre is the worst area but the problem infact is caused by the tail lights, the sealent on the taillights have worn out and leaks water into the interior of the boot, and hence the water finds its way under spare tyre wat i did to remove the leak was pull out both rear lights, done easily from the inside of the boot, unplug the wires take out the screws and push the lights out, then find a good sealant from an autoshop and reseal it , but make sure that u clean out the junk of the old worn out sealant 1st, its disgusting, but u will find after applying the new seal there wont be nemore leaks :P and u can easily fix the rust

Another R33 rust area is around the drivers side window wiper shaft, just as it comes out of the cowling under the black plastic escutcheon There is an indentation around it with no way for water to drain. I had to drill out one of the bolts that secure the shaft to the cowling as it was rusted and seized. A small hole drilled in the depression will fix it....

  • 1 month later...

Best rust treatment i know of is cold galv, but kill rust does the same job with a gloss finish, dont know if it comes in a spray though. I usually clean off rust spray cold galv then with a matching gloss

Another spot for rust is the engine bay chassis rails there is a folded sheet that runs along the top and rust gets between seen this on a import that was rejected because of it. They cut out the chassis no. and took all the id plates.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lucky man, who owns it in the family? Any pics? 
    • The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...