Jump to content
SAU Community

R31 Speedo Drive Question - Rb20 Box

Simon-S14
 Share

Recommended Posts

Simon-S14 Grand Master

Simon-S14

Posted
Posted

gday all, I just put a RB20 box into the 31 and used the 20 electric speedo drive since the R31 one was rooted. Now the 20 drive has a 2 pin plug that does not match the 3 pin plug of the 31 drive so i cut them of and soldered the wires together.

However the RB20 drive has two wires, a Black and a Green while the 31 loom has 3 wires, black, red and a yellow (with a blue wire further up tapped into the red wire) So i wired the Black to black and Red to the green on thge loom to the RB20 drive.. and just taped up the yellow wire.

Now the speedo does not work until about 40 kph, where the needle suddenly works and reads very inaccuratally (at 60 kph it says 140 kph)

any idea's what i need to do to make it work, or should i just get a 31 speedo drive.

Cheers

Simon

Link to comment
https://www.sau.com.au/forums/topic/142959-r31-speedo-drive-question-rb20-box/
Share on other sites
RB20_ZED Collaborator

RB20_ZED

Posted
Posted

if i were u, id take off the gearbox connection, hook a multimeter up to the wires and spin the little nob in the gearbox connector by hand to see what output the wires have...

u mite see that the red/black combo puts out current in one "spinning" range and the black/yellow in another... i.e. u may need to connect both the red/yellow onto the green...

BUT this is just my thoughts...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      Hows your intake piping? Are you still running stock? Having in the stock AFM position would mean, if the BOV was shut/venting out, it'd create the almost stalling kind of effect right // "the rich pulse behaviour" due to MAF thinking air is flowing ? But this would be better than having the bov in the stock position + MAF on/just before cross over piping right?
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      Essentially, yes. Although I wouldn't put the AFM on the crossover pipe. I'd want to put it into what amounts to the correct size tube, which is more easily done in the intercooler pipework. I bought a mount tube for card stile AFM that replaces the stock AFM - although being a cheap AliExpress knockoff, it had not flange and I had to make and weld my own. But it is the same length and diameter as the stock RB AFM, goes on my airbox, etc etc. I don't have a sick enough rig to warrant anything different, and the swap will take 5 minutes (when I finally get around to it and the injectors & the dyno tune).
    • Wazmond
      Stock rb25det neo questions

      By Wazmond · Posted

      So to summarise, the best thing to do is to move recirc to between turbo and IC, and maf on the crossover pipe. Meaning I'd need a recirc flange, drill a hole in the piping on turbo outlet area. And drill hole on crossover to fit/weld maf sensor? Either that or put the MAF on the turbo inlet right?  Is an aftermarket recirc/blowoff valve recommended? Do currently have family in Japan so could probably bring something back with maybe a cheeky lil SuperAutobacs run?
    • tsuokun
      Lets play a game - What is causing my oil consumption?

      By tsuokun · Posted

      Yep, so far most have said that it looks like corrosion on the wall from piston not moving. Which then has probably damaged the oil rings and caused those vertical marks. The longest the engine was still after the rebuild, was the winter of 2018 - 2019, plus the boat trip to Japan. When I shipped the car, it had normal gas in the tank but before that winter pause, it had E85 in tank.  In any case, even if either one of those was the cause, it happened close to 6 years ago and the car has been driven something like 30 000kms after the fact. Again, apart from the plugs and the dip stick, there is nothing in the way the car runs that would indicate what has been going on in the engine. I am going to consult a shop and ask their opinion, what would be the best approach. I do have some access to a garage I could use to diagnose further myself, but time is very restrictive. Might end up buying another engine that could be used while this one is being remedied. Without pulling the head, it will be impossible to find out if it needs another bore, but here's to hoping a hone would suffice.  Goddamnit, I would really have preferred this not happening.  
    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
×
×
  • Create New...