Jump to content
SAU Community

Recommended Posts

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

guys i can confirm that the group buy is going ahead

i have sent the peolpe interested the bank details

if i have missed you let me know and i will send the details to you

any other questions let me know and i will try and answer them

As for the type of bulb thats in you car the best thing to do i take out a bulb and show a auto shop that sell lights to find out which bulb it is

hey mate, im wanting set in h3,how does the 8000k look on road compared to 6000k? and do these do the same start up colour change as the euro cars do(starts blue then goes white).

thanks

the 6000k is a pure white colour

the 8000k is more of a blue

the best to go for is the 6000k as you can see better on the road with the pure white rather than the blue

let me know if your interested

last day to put your order in

ive been told order will be in next week so hopefully end of next week or the start of the following week you should have your kits.

Thanks mate, sounds good. :P

hi guys

All the Kits have been sent out

you should recieve them b4 the end of the week

thanks

if i get more interest on these lights i will start another group buy

just depend on how many people interesed because i need 5ppl to get at this price

Edited by nismos15
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Half anticipating the next question then: I have two magnets stuck in my oil pan. What should I do? 
    • If it's magnetic what is stopping you from using a magnet on a thin wire from fishing it out?
    • Those 2 solenoids in that assembly I mention, are the PWM solenoids for torque converter lock-up clutch & EPC (line pressure control) ~ when most folks hear of 'solenoid failure', the tendency is to think electrical failure...but fact of the matter is, especially wrt the EPC solenoid (which is moving/running all the time), you can have an electrically 'good' solenoid, that's absolutely broken/worn out mechanically inside...ie; valve plunger return spring rubbing against spring retainer plate, lowering preload pressure.. ...and the solenoid armature extension limit spring wafer with bad wear/broken off petals... ...and if there's ever been any metal flying about, damage to the valve plunger end itself... ...the stuff one never really sees, unless you go the whole 10yards trying to answer the question "why is my line pressure screwy, but TCU isn't flagging any EPC solenoid fault?"...and carefully dissect the solenoid. Worst (and most probable) scenario is when the plate spring petals break off, they get held by the magnetic flux, get mashed up by the armature into little bits, which end up in the space between the armature & shading core bore, and things get stuck or randomly jam up, and your line pressure goes flat and doesn't change...and the TCU never sees it, as it doesn't actively monitor LP... ..then it gets into insidious land, if you end up with lower than expected line pressure...lets say high clutch..and the lower pressure causes it to slip ~ when I say 'slip', think say 2000rpm on the drive plates, and 1800rpm on the driven plates, because the slip is making them under-rotate by 200rpm ; you get all the usual nasties like heat and band/clutch wear, but even if it's only 20rpm slip the same thing happens...and... you'll hardly ever pick this up driving the thing with the torque converter active as it effectively masks these sorts of slippages that are line pressure related ...(the newer TCUs can detect clutch slip rate)...just  FYI as it were...  
    • There's nothing that some paddle pop sticks and extra cable ties can't fix.
    • Hey guys, so Golebys has good prices on Bosch injectors, and also sell an adaptor to go from 1/2 length injector to standard with the Nissan 10.5mm top seal.  Does anyone know if that adaptor is to suit the 14mm or 11mm injector tops?  And re. The bottom seal, to suit my standard RB20 intake, would I be right in saying I can just slip the 14mm square section O ring over the bottom of the new injector and done? Thanks in advance guy, Cheers, Rowdy
×
×
  • Create New...