Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Alan if u get into trouble give me a buzz we'll sort something out for techsport

Thanks mate, I should be OK but will let you know if not.

Car is just about ready to go so I am really looking forward to this plus the few tweeks to prepare it for this event. :happy:

I'll be there in the evening too.

Anyone need a lift?

It's going to be pretty lonely in my car.....

Oh poiter!!!!

If i wasnt already driving i would come along :P

Just take your CB so you have some "chats" to the truckies on the way

I'll be heading up in the (sat)morning if anyone wants to come up the back way with me....

I'll be going up in the morning. I'm in Glenroy, so its pretty easy for me to get straight onto the Hume, but i'm interested to see this back way you always go. How far out of my way will it be to go the back way. Where is the best place to meet and how early are you going.

I think Roy is going up in the morning as well.

If you live in the city, its much quicker to just go the Hume.

To go the back way, youd pretty much add and hour and 1/2 to your trip.

We only go that way coz its quicker (and funner) when you live out that way.

Yeah what bec said, except it's probably only half an hour or so to your trip.... i just hate the Hume, so boring...

but for anyoen who does want to meet me....

up maroondah hwy to yara glen -> yea -> seymour -> shep

There is a little servo on the left on the main road before you turn off to yarra glen (the big Y split, we turn left to yarra glen not to healsville.) only 5 mins out of lilydale....I'll be there at about 5:30am and will leave there about 5:40am (I want maccas breaky in shep).... If anyone wants to come meet me there.... I'll have a CB as well..... channel 14.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...